background image

16 

PRS-UM-BTN-EN-Rev02-02.2019 

Warranty Statement 

All products are designed and manufactured to the latest internationally recognized standards 
by Prosense Technology under a Quality Management system that is certified to ISO 9001. As 
such Prosense Technology warrants its products against defective parts and workmanship and 
will repair or (at its option) replace any instruments which are or may become defective under 
proper use within 12 months from date of commissioning by an approved Prosense 
Technology representative or 18 months from date of shipment from Prosense Technology, 
whichever is the sooner. This warranty does not cover disposable batteries or damage caused 
by accident, abuse, abnormal operating conditions or poisoning of sensor. 
 
Defective goods must be returned to Prosense Technology premises accompanied by a 
detailed description of any issue. Where return of goods is not practicable Prosense 
Technology reserves the right to charge for any site attendance where any fault is not found 
with he the equipment. Prosense Technology shall not be liable for any loss or damage 
whatsoever or howsoever occasioned which may be a direct or indirect result of the use or 
operation of the Contract Goods by the Buyer or any Party. 
 
This warranty covers instrument and parts sold to the Buyer only by authorized distributors, 
dealers and representatives as appointed by Prosense Technology. The warranties set out in 
this clause are not pro rata, i.e. the initial warranty period is not extended by virtue of any 
works carried out there under. 
 
In no event will Prosense Technology be liable for any incidental damages, consequential 
damages, special damages, punitive damages, statutory damages, indirect damages, loss of 
profits, loss of revenues, or loss of use, even if informed of the possibility of such damages. 
Prosense Technology's liability for any claims arising out of or related to this product will in no 
case exceed the order value. To the extent permitted by applicable law, these limitations and 
exclusions will apply regardless of whether liability arises from breach of contract, warranty, 
tort (including but not limited to negligence), by operation of law, or otherwise. 

Содержание BTN Series

















Отзывы: