17.
Attach end caps by screwing the 1/4-20 X 9/16" narrow shoulder hex
screw through the threaded end cap and into the hole in the load bar
using the provided ProRac hex wrench.
16.
1.
Attach the U-clips to the four sliding rack anchors.
Work Rack Installation Instructions
54” and 72” Load Bars
ProRac Systems Inc.
7109 31
st
Avenue North
Minneapolis, MN 55427-2848
Toll Free: 1-800-217-7133
Phone: 763-546-5620
Fax: 763-546-0933
WWW.PRORAC.COM
Package Contents:
(2) 54” or 72” Load Bar
(4) 1/4 Split Washers
(1) Lo Pro Track Kit
(12) Flanged Washers
(4) 1/4-20 X 2-1/4” Button Head Screws
(12) Cap Covers
(12)1/4-20 X 1-1/2” Button Head Screws (4) Feet
(4) End Caps
(6) Sliding Tie Downs
(1) Hex Wrench
(1) 3 oz tube Silicone
(4) U-Clips
(4) Sliding Rack Anchors
(12) 1/4-20 Nuts with Integral Lock Washers
(4) 1/4-20 X 9/16" Narrow Shoulder Hex Screws
Photo shown with optional sliding load stops and 72” load bars.
Place the ¼” split washer onto the 1/4-20 x 2-1/4” screw.
Position the load bar and selected mounting hole over the foot and
sliding anchor.
3.
Make certain that
the U-clip is oriented
as shown!!!
Slide the 1/4-20 x 2-1/4” screw with the ¼” split washer through the
load bar and foot and screw into the sliding anchor using the provided
ProRac hex wrench.
PRO RAC GUIDELINES
2.
Please review the instructions and warranty carefully. Assembly and installation are the purchaser’s responsibility and beyond ProRac’s control.
Therefore, ProRac exclusively limits its warranty to the repair or replacement of a defective ProRac product for up to three years from retail
purchase. Warranty excludes damage to your vehicle, cargo, or any person or property during assembly, installation, and use.
♦
Do not carry more than 150 pounds (68KG) of combined cargo and accessories on ProRac load bars. ProRac load bars do not increase
gutter or roof strength. ProRac cannot warranty loads that exceed this limit.
♦
Do not use ProRac load bars and accessories for purposes other than those for which they were designed. Do not exceed their carrying
capacity. Failure to follow these guidelines or the product instructions will void the warranty.
This step is performed on a workbench or floor, not on a vehicle.
♦
Make sure all knobs, bolts, screws, straps, and locks are firmly attached, tightened, and locked before every trip. All fasteners must be
periodically inspected for signs of wear, corrosion, and fatigue. Check your load at stops during long trips to ensure continued fastening
security.
Lay the tracks side by side with the raised rib sides of the
anchors facing each other.
♦
Check all local and state laws governing projection of objects beyond the width and length of vehicle. Be aware of the width and height of your
cargo since low-clearance branches, bridges, and parking garages can affect the load. Never drive with any lock, knob, or rack in an open or
unlocked position. All long loads such as, but not limited to, sailboards, surfboards, kayaks, canoes, and lumber must be tied down front and
rear to the bumpers or tow hooks of the vehicle.
Place the molded feet over the anchors. Place the load bars on
top of the feet and select one of three mounting positions which
corresponds best with your application.
♦
Remove your rack and accessories when they are not in use and before entering automatic car washes.
♦
All locks must be turned and moved periodically to ensure smooth operation. Use graphite or similar dry lubricant. Locks are designed to deter
vandalism and theft. Remove valuable gear if your vehicle is unattended. Replacement keys are available only through your ProRac dealer.
Position the load bar and selected mounting hole over the foot
and screw the 1/4-20 X 2-1/4” button head screw through the
foot and into the sliding anchor.
♦
All cargo will affect the vehicle’s driving behavior. For your safety, adapt your speed to the conditions of the road and load being carried. Obey
all posted speed limits and traffic cautions.
♦
Due to their wind resistance, do not carry disks or wheels with covers on the ProRac bike carrier.
Consult your ProRac dealer if you have questions regarding the operation and limits of ProRac pr
The load bars are used only for positioning the track and will be
removed later.
Slide the three sliding tie downs and two crossbar sliding rack anchors
onto the track, alternating tie downs and rack anchors.
♦
information carefully.
oducts. Review all instructions and warranty
©
2005
ProRac
Systems,
Inc.
Revised
7-19-05
FGWR0 4-IA
5
