ProMinent Sigma / 2 Basic Type SBKa Скачать руководство пользователя страница 6

Страница: 6 / 52

Safety chapter

CAUTION!
These operating instructions include notes and quotes from

German guidelines relating to the system operator's scope of

responsibility. This information does not discharge the oper‐

ator from his responsibility as an operator and is intended

only to remind him or make him aware of specific problem

areas. This information does not lay claim to being complete,

nor applicable to every country and every type of application,

nor to being unconditionally up-to-date.

The following signal words are used in these operating instructions to

denote different severities of danger:

Signal word

Meaning

WARNING

Denotes a possibly dangerous sit‐

uation. If this is disregarded, you

are in a life-threatening situation

and this can result in serious inju‐

ries.

CAUTION

Denotes a possibly dangerous sit‐

uation. If this is disregarded, it

could result in slight or minor inju‐

ries or material damage.

The following warning signs are used in these operating instructions to

denote different types of danger:

Warning signs

Type of danger
Warning – hand injuries.

Warning – high-voltage.

Warning – hot surface.

Warning – danger zone.

Only use the pump to meter liquid metering chemicals.

In potentially explosive atmospheres in zone 1, device category II 2G,

explosion group II C, only operate the pump with the appropriate

nameplate (and the respective EC Declaration of Conformity) for

pumps for use in areas at risk of explosion in compliance with Direc‐

tive 94/9/EC in accordance with the European guidelines. The explo‐

sion group, category and degree of protection specified on the label

should correspond to or be better than the conditions given in the

intended field of application.

Only start up the pump after it has been correctly installed and com‐

missioned in accordance with the technical data and specifications

contained in the operating instructions.

Identification of safety notes

Warning signs denoting different types of

danger

Intended use

Safety chapter

Содержание Sigma / 2 Basic Type SBKa





















































Результаты поиска

Содержание Sigma / 2 Basic Type SBKa

Отзывы:

Похожие инструкции для Sigma / 2 Basic Type SBKa

Бренды по названию

Популярные бренды

ProMinent Sigma / 2 Basic Type SBKa, Руководство по эксплуатации

Результаты поиска

Содержание Sigma / 2 Basic Type SBKa

Отзывы:

Похожие инструкции для Sigma / 2 Basic Type SBKa

Бренды по названию

Популярные бренды