ProMinent DULCOTROL DWCa Скачать руководство пользователя страница 91

Страница: 91 / 140

CAL F-

Immerse sensor in buffer 2

Two point calibration

A1041

Sensor value

Sensor voltage

Start with <CAL>

4.88 ppm

144.2 mV

Fig. 55: Fluoride sensor calibration (CAL)
8.

Immerse the sensor in test container 2 with calibration solu‐

tion. When doing so gently move the sensor

Then press

[Calib. in progress] .

10. Then press to adjust the ppm value or press to con‐

tinue with the calibration

11. Then press
12. Import the result of the calibration into the controller memory

by pressing the key

The controller displays the continuous display again and

operates with the results of the calibration.

Incorrect calibration
Should the result of the calibration lie out‐

side the specified tolerance limits, an

error message appears. In this case the

current calibration will not be applied.
Check the prerequisites for the calibra‐

tion and clear the error. Then repeat the

calibration

15.1.3.3

1-point fluoride sensor calibration (CAL)

Correct sensor operation
–

Correct measuring and metering is only pos‐

sible if the sensor is working perfectly

–

Observe the sensor operating instructions

–

The carrying out of a 2-point calibration is

strongly recommended and is to be preferred

to other methods

–

For calibration the sensor must be removed

and refitted in the in-line probe housing. To do

this, observe the operating instructions of your

in-line probe housing

Material required for calibration of fluoride sensors:

One test container with calibration solution

Calibrating the controller diaLog DACb

Содержание DULCOTROL DWCa













































































































































Результаты поиска

Содержание DULCOTROL DWCa

Отзывы:

ProMinent DULCOTROL DWCa, Руководство по сборке и эксплуатации, Страница: 91 / 140

Результаты поиска

Содержание DULCOTROL DWCa

Отзывы: