ProMinent DULCOTROL DWCa Скачать руководство пользователя страница 127

Страница: 127 / 140

Ambient temperature: +5 ... +50°C
Medium temperature: max. sample water temperature 45 °C
Medium temperature: max. sample water temperature 65 °C, for

sample water “H”.
Medium temperature: max. sample water temperature 35 °C, for

the measured variable fluoride.

Air humidity: max. 90 % relative air humidity, non-condensing.

Degree of protection: IP 65

The transport weight depends on the configuration of the meas‐

uring plate and lies between 8 ... 13 kg.

Free flow / No overpressure or negative pressure
Make sure that there is no overpressure > 1 bar

and also no negative pressure at the outlet of the

measuring plate. Overpressure damages the

bypass fitting. Negative pressure damages the

sensors fitted. Use the stopcocks to adjust the

pressure at the sample water inlet and outlet.

Route the pipework so that the sample water can

drain unimpeded.

Temperature data

Climate

Protection against contact and mois‐

ture (IP)

Transport weight

Technical data and operating parameters

127

Содержание DULCOTROL DWCa













































































































































Результаты поиска

Содержание DULCOTROL DWCa

Отзывы:

ProMinent DULCOTROL DWCa, Руководство по сборке и эксплуатации, Страница: 127 / 140

Результаты поиска

Содержание DULCOTROL DWCa

Отзывы: