ProMinent DULCOTROL DWCa Скачать руководство пользователя страница 113

Страница: 113 / 140

16.1.1 Calibration of the cell constant

A1865

CAL

CELLCONST

CAL CELLCONST

TCoeffCAL

1.90%/°C

COND= 43,2

µS

/cm @25°C

CAL=CONTINUE

ZERO

CAL CELLCONST

CAL_T= 155.0 °C

COND=

CAL CELLCONST@25°C

043,975

µS

/cm

CELLC

CAL CELLCONST

1.0000cm

-1

CAL=ACCEPT

TCOEFF

Fig. 79: Calibration of the cell constant

Press and use the or key to move the cursor to

[CELLCONST] and confirm with .

Enter the temperature coefficient of the calibration solution.

The temperature coefficient of the calibration

solution is specified on the storage tank for

the calibration solution.

Confirm with .

Now dip the sensor into the calibration solution and gently

move the sensor.

Wait until the conductivity and temperature measured value

has stabilised.
Press .

The conductivity value measured is displayed.

Now use the , or keys to set the conductivity value

measured, in accordance with the conductivity value speci‐

fied on the calibration solution.

If calibration has been completed successfully, the con‐

troller stores the determined values for the cell constant

and the error checks relating to the measured value are

restarted. The numerical setting range of the cell con‐

stant is not limited.

Press twice to return to the continuous display.

Calibration compared to a calibration

solution

Calibrating the compact controller for inductive conductivity

113

Содержание DULCOTROL DWCa













































































































































Результаты поиска

Содержание DULCOTROL DWCa

Отзывы:

ProMinent DULCOTROL DWCa, Руководство по сборке и эксплуатации, Страница: 113 / 140

Результаты поиска

Содержание DULCOTROL DWCa

Отзывы: