promesstec UMU-FD 2 Скачать руководство пользователя страница 6

 

promesstec  GmbH

  I  Niedersachsenstraße 4  I  D- 48465 Schüttorf  I  Tel.:+49 (0)5923/ 90 229 0  I  Fax:+49 (0)5923/ 90 229 29 

E-Mail: [email protected]  I  Internet: www.promesstec.com   

 

 

3.  Safety instructions 

 
 

 
More  important  safety  instructions  can  be  found  in  the  individual 
chapters. 
 

 
Definitions: 

 

Dangerous voltages 

are defined as the ranges

:

 75...1500 75...1500 volts DC and 

50...1000 volts AC. 
 

 

Technicians 

are qualified persons who are trained or instructed to carry out an in-

stallation, operation or possible troubleshooting that is justifiable from a technical as 
well as from a safety point of view. 
 

Operating personnel 

are persons who set or operate the pushbuttons or potentiom-

eters of the product during normal operation and who have been made familiar with 
the content of this manual. 
 

Reception and unpacking: 

Unpack the device without damaging it and check upon receipt that the device type 
corresponds to what you ordered. The packaging should remain with the device until 
it is installed in its final location. 
 

3.1  Intended use of the product 

  
 

Environmental conditions: 

 
Direct sunlight, strong dust formation or heat, mechanical shocks and impacts are to 
be avoided; the device must not be exposed to rain or excessive moisture. If neces-
sary, heating that exceeds the specified limits for the ambient temperature must be 
prevented with the help of a cooling fan. The device must be installed in pollution 
degree 2 or better. 
 

 

Содержание UMU-FD 2
















Отзывы: