Promax OL-612 Скачать руководство пользователя страница 30

Страница: 30 / 128

October 2014

Page

3 ADVANCED USER GUIDEBOOK

Up till now, you have already been familiar with the initial operations of the

functions of the function areas, buttons and knobs in the front panel of the

OL-612

oscilloscope. Based the introduction of the previous Chapter, the user

should have an intimate knowledge of the determination of the change of the

oscilloscope setting through observing the status bar. If you have not been

familiar with the above-mentioned operations and methods yet, we advise you to

read the section of "Chapter One Junior Users' Guidebook".

This chapter will deal with the following topics mainly:

►

Digital Storage Oscilloscope.

How to Set the Vertical System.

How to Set the Horizontal System.

How to Set the Trigger System.

How to Implement the Sampling Setup.

How to Set the Display System.

How to Save and Recall Wave Form.

How to Implement the Auxiliary System Function Setting.

How to Implement the Automatic Measurement.

How to Implement the Cursor Measurement.

How to Use Autoscale function.

How to Use Executive Buttons.

►

Logic analyzer.

How to set sampling system.

How to set trigger system.

How to set threshold.

How to set display system.

How to set BUS.

How to measure.

How to save and recall.

How to use USB Mass storage device to storage.

How to search.

How to review setting info.

How to use cursor measurement.

How to set Utility.

It is recommended that you read this chapter carefully to get acquainted the

various measurement functions and other operation methods of the

OL-612

oscilloscope.

Содержание OL-612

































































































































Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды

Promax OL-612, Руководство пользователя

Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды