Promax OL-612 Скачать руководство пользователя страница 120

Страница: 120 / 128

October 2014

Page

115

5 TROUBLESHOOTING

►

In the case of that the oscilloscope is still in the black-screen state

without any display after the power is switch on, implement the

following fault treatment procedure.

Check whether the power connection is connected properly.

Check whether the power switch is pushed down to the designated

position.

Restart the instrument after complete the checks above.

If this product still can not work normally, please get in touch with

Lilliput and we will be under your service.

►

After acquiring the signal, carry out the following operations if the

wave form of the signal is not displayed in the screen.

Check whether the probe is properly connected to the signal

connecting wire.

Check whether the signal connecting wire is correctly connected to the

BNC (namely, the channel connector).

Check whether the probe is properly connected with the object to be

measured.

Check whether there is any signal generated from the object to be

measured (the trouble can be shot by the connection of the channel

from which there is a signal generated with the channel in fault).

Make the signal acquisition operation again.

►

The measured voltage amplitude value is 10 times greater or

smaller than the actual value.

Check whether the channel attenuation coefficient and the attenuation

ration of the probe used in practical application is match.

►

There is wave form displayed, but it is not stable.

Check whether the

Source

item in the

TRIG MODE

menu is in

conformity with the signal channel used in the practical application.

Check on the trigger

Type

item: The common signal chooses the

Edge

trigger mode for

Type

and the video signal the

Video

. Only if a proper

trigger mode is applied, the wave form can be displayed steadily.

Try to change the trigger coupling into the high frequency suppress

and the low frequency suppress to smooth the high frequency or low

frequency noise triggered by the interference.

Содержание OL-612

































































































































Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды

Promax OL-612, Руководство пользователя

Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды