background image

PROLIGHTS - Astra 

Hybrid420

15

10 - MENU STRUCTURE

The following chart describes the MENU tree of the product, the terms shown in 

BOLD

 indicates the 

default settings.

MENU 

1 CONNECT

ADDRESS

DMX / WDMX

001

-512

sACN

001

-512

ARTNET

001

-512

DMX MODE STANDARD

Set DMX chart for Main Fixture.

WIRELESS

WDMX ON/OFF

ON/

OFF

Enable/Disable the wireless card.

WDMX MODE

TRANSMITTER/

RECEIVER

Allows  to  choose  whether  to  set 

the wireless on the Transmitter or 

Receiver.

WDMX  mode  is  unlocked  only  if 

WDMX ON / OFF is ON.

TX LINK

ON/

OFF

TX link unlock when the unit is set 

as a transmitter..

TX UNLINK

ON/

OFF

Disconnect the transmitter from all 

receivers.

TX  unlink  unlocks  only  if  WDMX 

mode is on transmitter.

RX RESET

ON/

OFF

Total reset of the receiver.

RX  reset  unlocks  only  if  WDMX 

mode is receiver.

IN TO WDMX (TX)

ON/

OFF

Enable/Disable  the  transmission 

of the DMX values via wdmx.

WDMX TO DMX 

(RX)

ON

/OFF

Enable/Disable the retransmission 

of  the  DMX  from  the  receiver 

to  the  other  units  connected  by 

cable to the receiver itself.

ETHERNET 

SETTING

ARTNET SETTINGS IP ADDRESS

Set IP address of the fixture.

NET

Set Net for ArtNet protocol.

SUBNET

Set Subnet for ArtNet protocol.

UNIVERSE

Set Universe for ArtNet protocol.

sACN SETTINGS

IP ADDRESS

Set IP address of the fixture.

UNIVERSE

Set Universe for sACN protocol.

MERGE MODE

OFF

/HTP/

LTP

Set  Merge  Mode  for  sACN 

protocol.

ETHERNET TO 

DMX

ON

Enable / Disable DMX 

retrasmission  from  sACN/ArtNet 

signal to DMX out port.

OFF

Содержание Astra Hybrid420













































Отзывы: