Proficient Audio Systems M6, Быстрый старт

Страница: 1 / 5

Audio Systems
M6 QUICK START GUIDE
M6 SpECIfICATIonS
For technical inquiries, please call 877.888.9004 or email us at
techsupport@proficientaudio.com. We are available to assist you every
weekday, except holidays, between the hours of 7:00 a.m. and 5:00 p.m. PST.
Audio Systems
940 Columbia Avenue, Riverside, CA 92507
877 .888.9004 • Fax 951.750.6304 • proficientaudio.com
Audio Sections
Rated Power/Channel (RMS, 2 channels driven into 8 Ω) 30 Watts, 20Hz - 20kHz
THD (at rated power) < 0.7%
Power/Channel (RMS, 2 channels driven into 4 Ω
) 45 Watts @ 1kHz
Input Sensitivity (For rated power @ max VC) 300 mV
Input Impedance (source inputs)
> 22 kΩ
Input Overload (source inputs) 2.5 V
Output Voltage @ Pre-Outs
1.7 V, VC Setting, VC Max
(w/300 mV @ source inputs) 810 mV, NVC Setting
Output Impedance (pre-outs) < 300 Ω
Frequency Response (@ 1 watt @ 8 Ω)
20Hz - 20kHz ± 1.5dB
Channel Separation > 50dB @ 10kHz
Crosstalk Between Sources
> 65dB @ 10kHz
S/N Ratio (re: rated output, IEC A, source inputs shorted) > 95dB , VC 20dB below FCW
Bass Control Range ±10dB @ 100Hz
Treble Control Range ±10dB @ 10kHz
fM Tuner Sections
Tuning Range 87.5MHz - 108MHz
Usable Sensitivity (IHF, 98.1MHz) 12dBf Mono
Sensitivity (50dB quieting, 98.1Mhz) 18dBf Mono, 45dBf Stereo
S/N Ratio (65dBf, 98.1MHz)
75dB Mono, 65dB Stereo
Frequency Response (Mono or Stereo) 35Hz-15kHz ±3dB
Separation (@ 1kHz, 65 dBf)
>40dB
THD (1kHz, 65dBf, 98.1MHz) 0.15% Mono, 0.2% Stereo
Capture Ratio (45dBf)
2.0dB
Alternate Channel Selectivity 65dB
AM Tuner Sections
Tuning Range 520kHz - 1710MHz
Sensitivity (20dB Quieting, 1000kHz loop antenna) 750 µV/m
Selectivity (@ S/N 20dB, ±10kHz) 30dB
S/N Ratio (400kHz, 10mV/m Input @ 1000kHz, 30% Mod) 46dB
THD (400Hz, 10mV/m Input @ 100kHz, 30% Mod) 0.7%
Image Rejection (1400kHz)
38dB
Control Sections
Contact Closure (dry) 2A, 30V AC/DC Max
Phone Page In – Voltage/Impedance Audio Line Level, > 22 kΩ
Doorbell/Status In 1 & 2, 3V - 30V AC or DC 10 mA @ 12V AC/DC
Common IR Out
– HI (high power)
9 V Active High, 82 Ω (110 mA Peak)
– LO (emitter power) 9 V Active High, 670 Ω (13 mA Peak)
Zone IR Outs – Voltage/Impedance 9.2 V Active High, 620 Ω (13 mA Peak)
Source IR Outs (and loop) – Voltage/Impedance 11.5 V Active High, 390 Ω (29 mA Peak)
Common Status Out (0-12V DC) 9.5 V @ 100 mA
General
Power Consumption No Signal (idle) 50 Watts
Power Consumption @ 1/8 Rated Power 110 Watts
(3.75 watts/channel)
Line Ratings (120V AC version) 120V AC, 1.8A
Rear Panel Fuse (120V AC version)
T5AL 250V
Line Ratings (230V AC versions) 230V AC, 0.9A
Rear Panel Fuse (230V AC versions)
T2.5AL 250V
Dimensions (H x W x D) 513/16" x 171/8" x 151/2"
148mm x 435mm x 394mm
Weight
29 lbs (13 kg)
ZonE STATUS LEDS
LED indicators and labels:
Six blue LEDs indicate
that one or more zones
are currently active
TUnERS
Indicators show broadcast
band, frequency, active zone
and mono/stereo
MASTER poWER SWITCh
When pressed in, the M6
permits zones to be turned
ON and OFF by keypad
InDICAToR LIGhT
Blue indicates the master
power switch is ON and one
or more zones are active.
Red is STANDBY
1301-72600
figure 1
M6 Front Panel Features
TO ANTENNA AMP
M6
Riverside , CA. USA
Made in Taiwan
RS232
PHONE (PAGE IN) DOORBELL / STATUS IN
1
2
CONTROL
PORT
FIRMW ARE
UPGRADE
OFF ON
CO MMON
IR OUT
LO HI
STAT US OUT: 0 to +12V
120V 60Hz 1. 8A ~
FUSE: T5AL 250V
DATA I/O
CONT ACT CL OSURE
EXPANSION PORTS
CO MMON
SOURCE 3
LO OP
OUT
IR
LO OP
L R
INPUTS
SOURCE 4
LO OP
OUT
IR
LO OP
L R
INPUTS
SOURCE 5
LO OP
OUT
IR
LO OP
L R
INPUTS
SOURCE 6
LO OP
OUT
IR
LO OP
L R
INPUTS
SOURCE 7
LO OP
OUT
IR
LO OP
L R
INPUTS
SOURCE 8
LO OP
OUT
IR
LO OP
L R
INPUTS
SPKRS
L
R+
+ –
–
ZONE 4
L R PRE-OU T
VC
NVC
KEYPA D
IR OUT
SPKRS
L
R+
+ –
–
ZONE 5
L R PRE-OU T
VC
NVC
KEYPA D
IR OUT
SPKRS
L
R+
+ –
–
ZONE 6
L R PRE-OU T
VC
NVC
KEYPA D
IR OUT
SPKRS
L
R+
+ –
–
ZONE 3
L R PRE-OU T
VC
NVC
KEYPA D
IR OUT
SPKRS
L
R+
+ –
–
ZONE 2
L R PRE-OU T
VC
NVC
KEYPA D
IR OUT
SPKRS
L
R+
+ –
–
ZONE 1
L R PRE-OU T
VC
NVC
KEYPA D
IR OUT
4 3 2 5
M6 fEA TU RES
M6 Mul ti-Z one Aud io Am plif ier /Co ntr olle r
(Re fer to
figu re 2)
The M6 is a si x-z one , ei ght -so urc e A udi o A mpl ifie r/C ont rol ler . It ser ves as the
“br ain s” o f th e en tire keyp ad syst em . Th e M 6 pr ovi des aud io sw itc hin g fo r ei ght
sou rce s w ith 30 wat ts per cha nne l pe r zo ne.
Also inc lud es tw o bu ilt- in AM /FM Tun ers tha t al low prog ram min g of up to 10 stat ion
pre set s p er t une r p er z one , th is u ltim ate ly allo ws tre men dou s fl exi bili ty in tha t
differ ent u ser s c an hav e d iffer ent f avo rite st atio ns p rog ram med in dif feren t z one s.
Doo RBE LL/ STA TU S In 1 & 2 JAC KS
The se 3.5 mm min i ph one trig ger inp uts wor k in
con jun ctio n w ith the PH ON E PA GE IN jac k. Whe n
trig ger ed, the pho ne inp uts can be tu rne d on as
prog ram med by pro fic ient Ed itor. If a udi o pa gin g is
not req uire d, t hes e 1
& 2
jac ks may als o be pog ram med
as
STA TU S in puts
for pow er m ana gem ent of s our ce or
zon e co mpo nen ts. The y ac cep t in put lev els of 3 V to 30V
AC or DC for the trig ger ON con diti on. The vol tag e le vel
must dro p be low 1V AC or DC for the OFF con diti on.
IR o UT
Thi s 3. 5m m m ini jac k, o ne for eac h zo ne, pro vid es ded ica ted Zon e IR
out put ini tia ted from the res pec tiv e zo ne inp uts . Th ey may con tro l
spe cifi c zo ne com pon ent s w hen you wan t to pre ven t th e co ntr ol o f it
from the oth er z one s.
EXp An SIo n p oRT S
RJ4 5 ja cks pro vid e fo r co nne ctio n of spe cia liz ed
RS4 85 con tro lle d pr oduc ts and for loo pin g to
add itio nal M6 con tro lle rs fo r zo ne exp ans ion
cap abi lity . A not her fun ctio n of the se por ts is tha t
you can con tro l in stal led syst em com pon ent s w ith
bi-d ire ctio nal dat a vi a to uch pan els or c om put ers
usin g RS 232 pro toc ol. Req uire s th e Pr ofic ien t
Con tro l M odul e.
RS- 232 DAT A I/ o
Com mun ica tio n po rt.
ph on E pA GE In JA CK
Thi s ja ck pro vid es i npu t po rtin g fo r au dio fee ds fr om
doo r m ike s o r o the r fo rm s o f p hon e o r d oor bel l
pag ing . Th e ja ck is p rog ram mab le by pro fic ien t
Edito r, to
tur n on as e ven ts, whe n tri gge red by the
DOORB ELL /ST ATU S IN Jac k.
Co nTA CT CLo SU RE
Pro vid es a si ngl e po le dry rel ay con tac t to act iva te
any dev ice tha t ca n be con tro lle d or trig ger ed by
a sw itc h cl osu re. The clo sur e ca n be prog ram med
with in pro fici ent Edi tor to be ac tiv ate d by keyp ad
pre sse s, C om man d L ibr ary IR , o r w ith in mac ros
for M omen tar y, T ogg le a nd O pen /Clo se Pair ed
ope rat ion s. S prin g-lo ade d te rm ina ls a cce pt w ire siz es
fro m 2 8 to 14 AW G. In ter nal re lay co nta cts ar e ra ted at
2A/ 30V AC or D C.
Co nTR oL po RT & fIR MW ARE UpG RA DE SW ITC h
3.5 mm 4-c irc uit min i ph one jac k al low s se ver al c ont rol fun ctio ns. All syst em
prog ram min g is acc om plis hed via thi s po rt u sin g pr ofic ient Ed itor i n co nju nct ion
with the mat ing
Tra nsf er C abl e. I
t al so acc om mod ate s fa cto ry firm war e up dat es
in con jun ctio n w ith the
fIR MW ARE UpG RA DE o ff/ on Sw itc h. B
e su re to lea ve
thi s sw itc h in the
off
po siti on at a ll t im es, exc ept , as inst ruc ted with in
pro fic ient
Edito r, w hen you are doi ng a fir mw are upd ate . Su ch upd ate s en sur e th at y ou can
alw ays hav e th e la test fun ctio nal ity im pro vem ent s in the fie ld.
Co MM on IR oU TpU T & hI/L o S WIT Ch
3.5 mm min i ph one jac k pr ovi des a co mm on IR out put der ive d fr om all of
the zon e IR inp uts and from keyp ad ini tia ted IR com man ds der ive d fr om
the int ern al I R lib rar y. H igh or l ow IR pow er o utp ut i s se t by mea ns of t he
hI/L o s wit ch. Set it t o th e Lo se ttin g w hen driv ing stan dar d lo w po wer
em itt ers (i.e , Pr ofic ien t IR sin gle fla she r). Se t it to the
hI p
osit ion whe n
driv ing a hi gh pow er e mitt er ( i.e , a bla ster ) fo r te ach ing IR com man ds int o
lea rni ng rem ote s. Cau
tio n: T
he
hI p
osit ion will dam age or d est roy low
pow er e mitt ers !
Co MM on ST ATU S o UT po RT
Thi s 3. 5m m m ini pho ne jac k w ill go hig h (+ 12V DC)
whe n an y zo ne is tur ned ON and will go LO W (u nde r 1V
DC) w hen the last zon e is tur ned OFF . T he max . ou tpu t
of t his jac k is 100 mA at 9 .5V DC.
IR o UT JAC KS
The se 3 .5m m m ini pho ne j acks , o ne f or e ach sou rce , p rov ide
ded ica ted IR ou tpu t to sp ecif ic s our ce com pon ent s. W hen a
sou rce is sel ect ed on a ke ypad , IR fun ctio n co mm and s ar e
rou ted dire ctly to tha t so urc e. T his pre ven ts cro ss- con tro l
int erf ere nce betw een tw o or mor e so urc es tha t ha ve
ide ntic al I R co mm and s.
IR Loo p JA CKS
The se s ix 3 .5m m m ini pho ne j acks , o ne f or e ach sou rce , a re
pro vid ed exc lus ive ly for zo ne exp ans ion ca pab ilit y w hen
usin g tw o or mor e M 6 co ntr olle rs. T hey per mit the
sou rce IR sig nal s fr om the add ed zon es to be ca rrie d to
the sou rce com pon ent em itt ers .
L & R A UD Io In & Loo p JA CKS
The se RCA jac ks – fo ur f or e ach sou rce – pr ovi de aud io
sig nal inp uts and buf fer ed loo p ou tpu ts, for eac h
sou rce . Th e bu ffe red out put s ca n be use d to driv e loc al
com pon ent s or loo p th e si gna ls to the sou rce inp uts of
oth er M 6 co ntr olle rs w hen usin g th em for zon e ex pan sio n.
IEC Ty pE AC
Mai ns rec ept acl e an d fu se mat es with inc lud ed AC
pow er c ord . A lso hou ses the rea r pa nel rep lac eab le AC
mai ns fus e (T 5AL 250 V fo r 12 0V, and T2. 5AL 250 V fo r
230V /24 0V)
L & R pR E-o UT JAC KS
The se RCA ja cks pr ovi de lin e le vel
aud io out put s fo r d riv ing ex ter nal
pow er a mpl ifie rs for add itio nal roo ms
with in zon es, whe re nee ded .
VC- nVC SW ITC h
The aud io out put from the PRE -O UT ja cks can
eith er be con tro lle d by the int ern al v olu me
con tro l of the M6 (VC po siti on) or be a fix ed
lin e le vel out put in the no vol um e co ntr ol
(n
VC p
osit ion ). I n ei the r ca se, the ton e co ntr ol
rem ain s av aila ble for roo m “E Q” s ett ing s.
KEy pAD Zo nE InpU TS
The se RJ4 5 te rm ina ls allo w fo r e asy
con nec tio n o f th e in ter -ro om w irin g
fro m k eyp ads in th e v ario us r oom s.
Nor mal ly thi s is ac com plis hed us ing
CAT 5 c abl e w ith ho me- run le ngt hs o f
up to 100 0'.
L & R Sp EA KER S TE RM In ALS
The se 4-c irc uit plu gab le scr ew -do wn
ter min als acc ept w ire siz es f rom 14 to
28 AW G. T hey al low qu ick co nne ctio n o f
the in ter nal am plif ier s to st ere o p airs of
spe ake rs i n th e v ario us z one ro om s.
fig ure 2
M6 Rea r Pa nel Fea tur es
An TEn nA A Mp po RT
Ant enn a A mp: O ne, F-t ype ter min al c onn ect s to Pro fic ien t A nte nna
Am p on ly. The Ant enn a A mp must be loc ate d as clo se to the
ant enn as as pos sib le. Con nec t th e A M an d FM ant enn as as sho wn
on the Ant enn a A mp, and the n co nne ct t he Ant enn a A mp to the
M6 with a ru n of RG typ e co axi al c abl e.
CAU TIO N:
Do NO T co nne ct a n an ten na dire ctly to the Ant enn a
Am p te rm ina l. T her e is DC vo lta ge pre sen t to pow er t he Ant enn a
Am p Co nne ctio n of di pol e an ten na will cau se a sh ort circ uit.
15 14 16
KEypAD ConfIGURATIonS
The M6 System comes with six single gang PMKIR
pre-configured keypads, one for each zone as shown
for the single gang version in figure 14. The cover
plates and the other configurations are optional.
Each keypad comes with a set of factory installed
“default buttons” plus a good variety of additional
buttons. The default buttons can be easily changed
to meet the needs of the installation.
The Proficient M6 System consists of four subsystems.
First, the keypads themselves can be configured in
many key icon arrangements and placed in a one,
two or three gang set-up to meet virtually any client
requirement. They are connected via convenient
CAT5 cable with home-run lengths of up to 1000'
(305m or longer, if heavier gauge wire is used) to the
centrally located M6 Multi-Zone Audio Amplifier/
Controller located near the controlled equipment.
The M6 contains the “brains” of the system, taking
key location data from the keypads to trigger the
actual controlling IR, RS232 and RS485 commands
that are passed to all of the installed system
components. Programming is accomplished by the
use of proficient Editor, a Proficient developed
Windows software system. A fourth item, the
optional Command Interface (sold separately), is an
installer’s tool for learning and teaching special IR
commands that are not included in the proficient
Editor internal library.
PMKIR PNK PFK
(included) (optional) (optional)
1 2 3
4 5 6
7 8 9
0
TRK DSC
RDM
RPT
PLAY
ESC INFO
MENU GUIDE
MUTE
PWR
PMKIR PNK
MUTE
PWR
1 2 3
4 5 6
7 8 9
0
TRK DSC
RDM
PMKIR
(included)
SAT CD
MUTE
TNR1 TNR2
PWR
SEL
CD2 MP3
BASS TREB
SAT CD
TNR1 TNR2
CD2 MP3
BASS TREB
GBL
RPT
SAT CD
TNR1 TNR2
CD2 MP3
BASS TREB
(included) (optional)
SAT CD
MUTE
TNR1 TNR2
PWR
CD2 MP3
BASS TREB
SAT CD
MUTE
TNR1 TNR2
PWR
CD2 MP3
BASS TREB
PLAY
ESC INFO
MENU GUIDE
SEL
1 2 3
4 5 6
7 8 9
0
DSC
RDM
RPT
TRK
1 2 3
4 5 6
7 8 9
0
DSC
RDM
RPT
TRK
Single Gang
Double Gang Triple Gang
1.77"
4.07"
PNK Numeric Keypad
(Not included with M6)
1 2 3
4 5 6
7 8 9
0
TRK DSC
RDM
RPT
Rear View
9
KEYPAD EXPANSION
Riverside, C A. USA • Made in China
proficientaudio .com
PNK
Numeric Keypad
1 2 3
4 5 6
7 8 9
0
DSC
RDM
RPT
TRK
PMKIR Master Keypad
(included with the M6)
MUTE
PWR
Rear View
01
23
45678
9A
BCD
EF
SAT CD
TNR1 TNR2
CD2
MP3
BASS TREB
PMKIR
Master Keypad
with IR Receiver
+ RELAY –
RELAY
+12V DATA GND 485
A
485
B
A
D
D
RE
SS
KEYPAD EXPANSIO
N
Riverside, CA. USA • Made in China
proficientaudi o.com
SAT CD
MUTE
TNR1 TNR2
PWR
CD2 MP3
BASS TREB
2 1
3 4
6
7
4
8
5
PFK Function Keypad
(Not included with M6)
PLAY
ESC INFO
MENU GUIDE
Rear View
2
9
SEL
KEYPAD EXPANSION
Riverside, CA. USA • Made in China
proficientaudi o.com
PFK
Function Keypad
PLAY
ESC INFO
MENU GUIDE
SEL PMKIR
Master Keypad
with IR Receiver
+ RELAY –
RELA
Y
+12V DATA GN
D
485
A
485
B
A
D
D
RE
SS
KEYPAD EXPANSION
Riverside, CA. USA • Made in China
proficientaudio .com
KEypAD fEATURES ConTInUED
KEypAD fEATURES
(Refer to figure 15)
1. pMKIR Source/function Buttons – Six of this set
of eight buttons are programmed as source select
for the M6. When the system is off, all buttons have
a background green color. When a source button is
pressed, it turns to a low-level red color to show that
it is the active source and the system is on.
2. Keypad Expansion Terminal – This 16-pin header
terminal is used to inter-connect the optional numeric
and function keypad modules for expansion as
needed. A ribbon cable is packed with each module for
making these connections.
3. Address Switch – A unique hex address must be
set for each master keypad when connected on a
common bus within a single zone. Unique addresses
are not required zone-to-zone. It provides up to 16
addresses (0 to F).
4. Snap Tabs – These tabs hold the decorator style
insert panel to the metal mounting plate and are
easily released for custom changing of the buttons.
5. Mounting plate – Standard plate allows the
keypad module to be attached to standard in-wall
J-Boxes using the two screws provided. Allows
attachment of standard decorator type cover plates
(also screwless snap-on plates).
6. IR Receiver Lens – Version PMKIR includes
Proficient’s exclusive ANS IR receiver, built-in. It allows
the use of a handheld remote for control of system
components.
7. Connection Terminals – for CAT5 home-run
termination. +Relay and – Relay - for future use.
+12V – Powers the keypad, including the internal IR
receiver on model PMKIR. Includes reverse voltage
protection. Data – Sends IR control signals for
control of system components. GnD – Return for
power, IR signal and data. 485 A / 485 B – Balanced,
bi-directional system communications data.
8. function Buttons – These lower four buttons (can
be programmed for any function except source select.
9. numeric and function Buttons – Require
programming via proficient Editor. All buttons glow
background green and can be configured to go off
after a set time, or stay on via proficient Editor.
figure 14
Keypad Configurations
figure 15
Keypad Features
M6 AUDIo ConTRoLLER WITh KEypAD SySTEM
The keypads come in four basic modules.
PMKIR
(12 buttons) and PMK (13 buttons) are the master
keypads and must be used in each system. As
mentioned earlier, the M6 comes with a pre-
configured version of the PMKIR, for the convenience
of the installer. It is usable right "out of the box" in
conjunction with a default project that is factory
programmed into the M6. The PMKIR includes an
IR receiver and has one less function button, but is
otherwise identical to the PMK. The PNK Numeric
(16 buttons) and
PFK
Function (14 buttons) keypad
modules can be thought of as “slaves” to the PMKIR /
PMK (they will not work alone), providing additional
key locations for numeric and function commands.
Limited Two-year Warranty
Proficient Audio Systems (“Proficient”) warrants to the original retail purchaser only (“you”) that
this product will be free from defects in materials and workmanship for a period of two years (the
“Warranty Period”), subject to the limitations and exclusions set out in this Limited Warranty. This
warranty is not transferable to subsequent owners of the product. If you discover a defect in material
or workmanship within the Warranty Period, you can obtain warranty service by contacting Proficient
during the Warranty Period at 877.888.9004 or techsupport@proficientaudio.com or by sending the
product to Proficient at 940 Columbia Avenue, Riverside, CA 92507 or to the dealer from whom you
purchased the product. Defective products must be shipped, prepaid and insured, together with
proof of purchase. Warranty service requests made without proof of date of purchase will be denied.
Freight collect shipments will be refused. It is preferable to ship this product in the original shipping
container to lessen the chance of transit damage. In any case, the risk of loss or damage in transit is
to be borne by the purchaser.
If, upon examination by Proficient or its authorized dealer, it is determined that the unit is in fact
defective, Proficient will, at its option:
• Repair or replace the product at no additional charge; or
• If the model is no longer available and can not be repaired effectively, replace the unit with a current
model of equal or greater value. In some cases where a new model is substituted, a modification
to the mounting surface may be required. If mounting surface modification is required, Proficient
assumes no responsibility or liability for such modification.
Proficient will bear the cost of returning the repaired or replaced product to you, freight prepaid.
All replaced parts and product become the property of Proficient Audio Systems. The foregoing is
your sole and exclusive remedy for breach of warranty. If the product is not found to be defective,
Proficient will contact you to arrange for return of the product to you, at your expense.
EXCLUSIonS:
• This Warranty does not include service or parts to repair damage caused by accident, disaster,
misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use, voltage
inputs in excess of the rated maximum of the unit, or service, repair or modification of the product
by unauthorized dealers. This Warranty also excludes normal cosmetic deterioration caused by
environmental conditions.
• This Warranty will be void if:
• the Serial Number on the product has been removed, tampered with or defaced.
• the product was not purchased from an authorized dealer.
ThE foREGoInG WARRAnTIES ARE EXCLUSIVE AnD In LIEU of ALL oThER EXpRESSED AnD
IMpLIED WARRAnTIES. pRofICIEnT EXpRESSLy DISCLAIMS ALL SUCh oThER WARRAnTIES,
InCLUDInG BUT noT LIMITED To IMpLIED WARRAnTIES of MERChAnTABILITy, fITnESS foR
A pARTICULAR pURpoSE AnD non-InfRInGEMEnT. In no event will Proficient be liable for any
incidental or consequential damages arising out of the use or inability to use the product, even if
Proficient has been advised of the possibility of such damages, or for any claim by any other party.
Notwithstanding the above, if you qualify as a “consumer” under the Magnuson-Moss Warranty Act,
then you may be entitled to any implied warranties allowed by law for the Warranty Period. Further,
some states do not allow limitations on how long an implied Limited Warranty lasts or allow the
exclusion or limitation of consequential damages, so such limitations may not apply to you.
ATTEnTIon To oUR VALUED ConSUMERS:
To insure that consumers obtain quality pre-sale and after-sale support and service, Proficient prod-
ucts are sold exclusively through authorized dealers. proficient products are not sold online by
Proficient or its authorized dealers, and this warranty is VoID if the products have been purchased
from any internet reseller. To determine if your Proficient reseller is authorized, please call Proficient
at 877.888.9004 or go to proficientaudio.com.