background image

www.usaprocom.com

3

200233-01B

NATURAL AND PROPANE/LP GAS: 

Natural 

and Propane/LP gas are odorless. An odor-

making agent is added to the gas. The odor 

helps  you  detect  a  gas  leak.  However,  the 

odor added to the gas can fade. Gas may be 

present even though no odor exists.

 WARNING: Any change to 

this heater or its controls can 

be dangerous.

 WARNING: Do not use any 

accessories not approved for 

use with this heater.

 WARNING: Carefully super-

vise young children when they 

are in the room with the heater.

  WARNING:  Make  sure  grill 

guard is in place before running 

heater.

 WARNING: Due to high tem-

peratures, the appliance should 

be located out of traffic and away 

from furniture and draperies.

 WARNING: Heater becomes 

very hot when running. Keep 

children and adults away from 

hot surfaces to avoid burns or 

clothing ignition. Heater will re-

main hot for a time after shutoff. 

Allow  surfaces  to  cool  before 

touching.

 WARNING: Do not place 

clothing  or  other  flammable 

material on or near the appli-

ance.  Never  place  any  objects 

in the heater.

SAFETY

IMPORTANT: Read this owner’s 

manual carefully and completely 

before trying to assemble, op-

erate, or service this heater. 

Improper use of this heater can 

cause serious injury or death 

from  burns,  fire,  explosion, 

electrical  shock,  and  carbon 

monoxide poisoning.

Only a qualified installer, service 

agent, or local gas supplier may 

install and service this product.

 WARNING: Keep the appli-

ance area clear and free from 

combustible materials, gasoline, 

and other flammable vapors and 

liquids.

 WARNING: This appliance 

can  be  used  with  propane  or 

natural gas. It is shipped from 

the factory adjusted for use with 

propane.

This appliance is only for use 

with the type of gas indicated on 

the rating plate. This appliance 

is not convertible for use with 

other gases.

 DANGER: Carbon monoxide 

poisoning may lead to death!

CARBON MONOXIDE POISONING:

 Early 

signs of carbon monoxide poisoning resemble 

the flu, with headaches, dizziness or nausea. 

If you have these signs, the heater may not be 

working properly. Get fresh air at once! Have 

heater serviced. Some people are more af-

fected by carbon monoxide than others. These 

include pregnant women, people with heart or 

lung disease or anemia, those under the influ-

ence of alcohol and those at high altitudes.

Содержание MNSD300HGA

































Отзывы: