Procom MNSD300HGA Скачать руководство пользователя

Страница: 24 / 32

www.usaprocom.com

200233-01B

TROUBLESHOOTING

Problem

Possible Cause

Corrective Action

Heater produces un-

wanted odors.

1. Heater is burning vapors from

paint, hair spray, glues, etc.

See IMPORTANT statement,

page 20.

2. Gas leak. See

Warning State-

ment

on of page 20.

3 Low fuel supply.

1. Ventilate room. Stop using

odor causing products while

heater is running.

2. Locate and correct all leaks

(see

Checking Gas Connec-

tions

, page 15).

3. Refill supply tank (Propane/

LP models).

Heater shuts off in use

(ODS operates).

1. Not enough fresh air is avail-

able.

2. Low line pressure.

3. ODS/pilot is partially

clogged.

1. Open window and/or door for

ventilation.

2. Contact local gas supplier.

3. Clean ODS/pilot (see

Care

and Maintenance

, page 19).

Gas odor exists even

when control knob is in

OFF position.

1. Gas leak. See

Warning

Statement

on page 20.

2. Control valve is defective.

1. Locate and correct all leaks

(see

Checking Gas Connec-

tions

, page 15).

2. Contact customer service.

Moisture/condensation

noticed on windows.

1. Not enough combustion/

ventilation air.

1. Refer to

Air for Combus-

tion and Ventilation

require-

ments, page 6.

SERVICE HINTS

When Gas Pressure Is Too Low

TECHNICAL SERVICE

You may have further questions about installation, operation, or troubleshooting. If so, contact

ProCom Heating, Inc. at 1-866-573-0674.
When calling, please have your model and serial numbers of your heater ready.

• pilot will not stay lit

• burners will have delayed ignition

• fireplace will not produce specified heat

• propane/LP gas supply might be low (pro-

pane/LP units only)

You may feel your gas pressure is too low. If

so, contact your local gas supplier.

Содержание MNSD300HGA

































Результаты поиска

Содержание MNSD300HGA

Отзывы:

Похожие инструкции для MNSD300HGA

Бренды по названию

Популярные бренды

Procom MNSD300HGA, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание MNSD300HGA

Отзывы:

Похожие инструкции для MNSD300HGA

Бренды по названию

Популярные бренды