Pro Mach ORION Sentry HP Скачать руководство пользователя страница 64

Страница: 64 / 100

Machine Manual

Orion

Sentry HP/ LP Flex Stretchwrapper

Revision 3.1

System Operation

21 May 2020

Page 3-32

Factory Defaults Screen

This is the Factory Defaults Screen. This screen allows authorized users to go back to the
factory default settings.

Figure 3 - 27

The Factory Defaults

Screen

Table 3-23. The Factory Defaults Screen Button Descriptions

STATE 1

DESCRIPTION

RESTORE FACTORY

DEFAULTS

Press this button to delete the currently entered factory settings and replace them
with the original factory default settings. This will replace all Wrap Settings,
Machine Settings, and Recipes with the factory default parameters.

RESTORE DEFAULT

NETWORK SETTINGS

Press this button to restore default network settings to the machine.

Содержание ORION Sentry HP





































































































Результаты поиска

Содержание ORION Sentry HP

Отзывы:

Похожие инструкции для ORION Sentry HP

Бренды по названию

Популярные бренды

Pro Mach ORION Sentry HP, Руководство пользователя

Результаты поиска

Содержание ORION Sentry HP

Отзывы:

Похожие инструкции для ORION Sentry HP

Бренды по названию

Популярные бренды