Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя

Страница: 71 / 132

Orion

Machine Manual

Revision 3.0

CTS Flex Stretchwrapper

25 July 2016

System Operation

Page 3-41

HMI Setup

This is the HMI Setup Screen. This screen allows you to choose the HMI language, set the

screen brightness, adjust the network settings, calibrate the touchscreen touch points, and

set the date and time.

Figure 3 - 30

The HMI Setup

Screen

Table 3-29. The HMI Setup Screen Button Descriptions

STATE 1

DESCRIPTION

ENGLISH

Press this button to switch the HMI text to English.

ESPANOL

Press this button to switch the HMI text to Spanish.

BRIGHTNESS

Use the slider to adjust the brightness of the HMI screen. Slide to the right to

increase the brightness. Slide to the left to decrease the brightness.

TOUCH CALIBRATION

Press this button to go to the touch calibration screen. This is used to set the align-

ment of the touch screen. There are multiple targets to press to align the screen.

NETWORK SETTINGS

When logged in as an Administrator, you can edit the IP Address, Subnet Mask,

Gateway, or Node number. Press save, when done editing. If you are not logged in

with the correct credentials, these settings are read-only.

Press this button to save the Network Settings. If you navigate away from the screen

without saving, the entered network settings will not take effect.

TIME AND DATE

Press the numbers to edit the time and date. The format is hours (01-24), minutes

(0-59), seconds (0-59). The date is set by year (####), month (1-12), and day (1-31).

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды