Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя | Manualshive

Страница: 22 / 132

background image

Machine Manual

Orion

CTS Flex Stretchwrapper

Revision 3.0

Introduction and Safety

25 July 2016

Page 1-12

Inspection

1.

Remove all packing and supporting additions - these may include the blocks under the

carriage and the restraining bar over the table.

Note:

When removing the packing materials covering the machine, care

must be taken not to cut any of the electrical wires and/ or polyure-

thane covering on the film carriage rollers.

2.

Perform a visual inspection of the electrical and mechanical parts for loosened joints

and / or broken connections. Any suspected shipping damage must be reported imme-

diately to the freight carrier. Any transport damage cannot be claimed to Orion Pack-

aging Inc.

Items that are vulnerable to damage and must be inspected are as follows:
• Motors and transmissions
• Junction boxes
• Electrical conduits
• Proximity and limit switches
• Photocells

3.

Check around the tower to ensure that there is no crippling of the movable parts i.e.

casters, center axle or drive assembly.

4.

Verify the following:

• Check wires and conduits for crushed sections or loose fittings.
• Verify the film carriage to be sure that it is correctly aligned with the tower
• Verify the tension on the lift belt.
• Verify all the dials and knobs on the control panel for smooth action.

Machine Installation

• After the visual inspection has been completed, the electrical power and the com-

pressed air (Optional) shall be connected as specified on the diagrams supplied with

the machine.

• An electrical diagram is provided with each machine in the envelope attached to the

panel box.

• Make sure the machine is on a level surface.
• Orion Packaging insist on a dedicated circuit be used for this wrapper. Extension cords

are not allowed and can void your warranty.

«
...
20
21
22
23
24
...
»

Содержание Orion CTS Flex Stretchwrapper





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренд: Ergoswiss Страницы: 27

Бренд: Zepro Страницы: 6

Бренд: Performance Tool Страницы: 2

Бренд: Jet Страницы: 8

Бренд: Jet Страницы: 12

Бренд: Jet Страницы: 12

Бренд: Vestil Страницы: 13

Бренд: Sky Elevator Страницы: 20

Бренд: Falco Страницы: 80

Бренд: HALDER Страницы: 2

Бренд: IDEAL Страницы: 46

Бренд: MAHA Страницы: 22

Бренд: Harmar Mobility Страницы: 25

Бренд: Halfen Страницы: 20

Бренд: Wahlberg Страницы: 40

MOBILIFT ECO 650

Бренд: Sabaj Страницы: 22

Бренд: Haklift Страницы: 8

Бренд: Vestil Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды