Princeton Instruments NIRvana-LN Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 122

Princeton Instruments NIRvana-LN Скачать руководство пользователя страница 89

Chapter 10

Troubleshooting

89

10.4 Data Overrun Due to Hardware Conflict Message Displayed

If this dialog appears when acquiring a test image, acquiring data, or running in focus mode,
check the array size and then check the DMA buffer size. A large array (e.g., a 2048x2048
array,) requires a larger DMA buffer larger setting than that for a smaller array (e.g., a
512x512 array.)

Figure 10-4: Data Overrun Due to Hardware Conflict Dialog

Perform the following procedure to change the DMA buffer size:

1.

Note the array size listed on the

Setup|Hardware|Controller/CCD

tab or on the

Acquisition|Experiment Setup|Main

tab

Full Chip

dimensions.

2.

Open the

Setup|Environment|Environment

dialog.

3.

Increase the DMA buffer size to a minimum of 32 MB (64 MB if it is currently 32 MB
or 128 MB if it is currently 64 MB), click on

OK

, and close WinSpec.

4.

Reboot the computer.

5.

Restart the application software, and begin acquiring data or focusing. If the problem
persists, increase the DMA buffer size again.

10.5 Detector Stops Working

Problems with the host computer system or software may have side effects that appear to be
hardware problems. If you are sure the problem is in the detector system hardware, begin
with these simple checks:

•

Turn off all AC power.

•

Verify that all cables are securely fastened and that all locking screws are in place.
Correct any apparent problems and turn the system on.

•

If the system still does not respond, contact Customer Support.

44

11-

0145

_0044

«
...
87
88
89
90
91
...
»

Содержание NIRvana-LN



























































































































Отзывы:

Нет отзывов