manualshive.com logo in svg

Princeton Instruments NIRvana-LN, Руководство пользователя, Страница: 59 / 122

Поделиться
Скачать
Princeton Instruments NIRvana-LN Скачать руководство пользователя страница 59

Chapter 6

WinSpec/32 and WinView/32 First Light Procedure

59

6.10 Shut Down Procedure

Perform the following procedure to shut down the system:

1. For liquid nitrogen cooled systems:

 Carefully empty the Dewar and store the liquid 

nitrogen that has been removed.

CAUTION!

!

Because of the low operating temperatures, cryogenically-cooled 
detectors must always remain powered ON when Liquid Nitrogen 
(LN) remains in the dewar.

Always keep the detector powered ON following the completion 
of all experiments until all LN has either been removed or 
allowed to evaporate from the dewar, and the detector has 
warmed up to ambient temperature.

WARNINGS!

1.

Always wear protective equipment when working with Liquid 
Nitrogen. Even minimal contact with LN can cause severe injury to 
eyes and skin. Avoid contact with the splashing that will invariably 
accompany the pouring of LN into a room temperature Dewar.

2.

Always be careful when removing the Dewar filler cap if there is 
LN present in the Dewar. Pressure due to nitrogen gas can cause 
the cap to fly out when the retaining nut is loosened, possibly 
spraying you with liquid LN, which can cause severe injury.

2.

Close WinSpec/32.

3.

Turn off spectrometer power (when applicable.)

4.

Turn off the detector power.

Содержание NIRvana-LN



























































































































Отзывы:

Нет отзывов