Princeton Instruments NIRvana-LN Скачать руководство пользователя страница 35

Страница: 35 / 122

Chapter 4

System Setup

Turn on the detector’s power supply.

Launch the application software and configure the external shutter as follows:

•

Within LightField:

—

Within Experiment Settings locate the Shutter expander and open it.

•

Within WinSpec/32:

—

Open the

Hardware Setup|Controller/Camera

tab.

—

Within the

Shutter Type

field, select

Custom

from the pull-down menu.

—

Click

to save the configuration and dismiss the Hardware Setup dialog.

The time it takes the shutter to completely close is approximately 8 ms.

NOTE:

Setting shutter compensation time will slow the readout rate.

4.8 Configure Default Parameters in LightField

Perform the following procedure to configure LightField with default system parameters:

Verify the NIRvana-LN (and spectrograph, if this is a spectroscopy system) is
connected to the host computer and that the detector (and spectrograph) power supply is
turned on.

Launch LightField.

While LightField is starting up, it will detect the available device(s) and load the
appropriate icons into the

Available Devices

area in the

Experiment

workspace.

When an icon is dragged into the

Experiment Devices

area, the appropriate

expanders and default values will automatically be loaded into the

Experiment

Settings

stack on the left-hand side of the window.

REFERENCES:

Refer to

Chapter 5, LightField First Light Procedure

on page 41

for step-by-step procedures and complete information about basic
system operation.

4.9 Configure Default Parameters for WinView/32 and WinSpec/32

Perform the following procedure to configure WinSpec/32 with default system parameters:

Verify the detector is connected to the host computer and that the detector’s power
supply is turned on.

Open the WinSpec application software.

The Camera Detection wizard

will automatically run if this is the first time a Princeton

Instruments WinX application (e.g., WinSpec/32, WinView/32, or WinXTest/32,) has been
installed with a supported detector.

Otherwise, when installing a new detector type, click on the

Launch Camera

Detection Wizard…

button on the

Controller/CCD

tab to start the wizard.

Содержание NIRvana-LN



























































































































Результаты поиска

Содержание NIRvana-LN

Отзывы:

Princeton Instruments NIRvana-LN, Руководство пользователя, Страница: 35 / 122

Результаты поиска

Содержание NIRvana-LN

Отзывы: