background image

OPERATING

INSTRUCTIONS

Dedicated Holding Bin

Model No. DHB2PT-30

DHB4PT-30 & DHB4-30

355 East Kehoe Blvd.   Carol Stream, IL  60188

Tel: (630) 462-8800 

 Fax:  (630) 462-1460

Toll Free:  1-800-PCASTLE

545-502revB 

     

Printed i

n

 USA 1/06 © 2006

This product is warranted to be free from defects in material 
and/or workmanship for a period of 1 year from date of original 
installation, not to exceed 18 months from the date of 
manufacture.
Any component which proves to be faulty in material and/or 
workmanship will be replaced or repaired (at the option of 
Prince Castle, Inc.) without cost to the customer for parts and 
labor. This warranty covers on-location service (i.e. trip 
charges and/or mileage). Travel mileage is limited to 100 miles 
(200 Kilometers) round trip (one trip warranty) from an 
authorized service agency or its sub-service agency.
This warranty is subject to the following exceptions/conditions:
•  Use of any non-genuine Prince Castle parts voids this 

warranty.

•  All labor to be performed during regular work hours. 

Overtime premium (the incremental amount) will be charged 
to the customer.

•  Damage caused by carelessness, neglect and/or abuse 

(e.g., dropping, tampering or altering parts, equipment 
damaged in shipment, by fire, flood or an act of God) is not 
covered under this warranty.

•  All problems due to operation at voltages other than that 

specified on equipment nameplates are not covered by this 
warranty. Conversion to correct voltage is the customer’s 
responsibility.

•  This equipment must be serviced by Prince Castle 

Authorized Service Agency or a Prince Castle Service 
Technician during the warranty period.

LIMITED WARRANTY

TABLE OF CONTENTS

PAGE

Installation ..................................................................... 2
Programming .............................................................. 2-3
Operating ....................................................................... 4
Cleaning ........................................................................ 4
Parts List ....................................................................... 4
Exploded View .............................................................. 5
Troubleshooting ............................................................ 6
Wiring Diagrams ........................................................... 7

ELECTRICAL SPECIFICATION

Model

Volts

  HZ

  Watts   Amps

DHB2-30

208

  60

   1800        8.6

DHB2-30L

120

  60

   1650      13.8

DHB2-30J

200       50/ 60        1650        8.3

DHB2PT-30

208

  60

   1800      8.7

DHB2PT-30L

120          60           1650       13.8

DHB2PT-30J

200

50/60

   1650      8.3

DHB2PT-30CE

220-240   50

   1900        7.9

DHB2PT-30GB

240

  50

   1900      7.9

DHB4PT-30

208

  60

    3600      17.3

DHB4PT-30J

200

50/60

    3400      17.0

DHB4PT-30CE

220-240   50

    3800      16.0

DHB4PT-30GB

240

  50

    3800      16.0

DHB4-30

208

  60

    3600      17.3

DHB4-30J

200

50/60

    3400      17.0

DHB4-30CE

220-240   50

    3800      16.0

DHB4-30GB

240

  50

    3800      16.0

DHB2PT-30

DHB4PT-30

     

DHB4-30 (Non Pass Through)

Содержание DHB2PT-30








Отзывы: