manualshive.com logo in svg

Primus D55, Руководство по обслуживанию, Страница: 52 / 82

Поделиться
Скачать
Primus D55 Скачать руководство пользователя страница 52

50

70276001

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

64. REVERSING TIMER

(Manual Timer Models)
Refer to Figure 21.

NOTE: All reversing electrical components except 
the reversing/nonreversing switch are located in the 
contactor box on the rear of the tumbler. The 
reversing/nonreversing switch is mounted on the 
exterior control box for manual timer models.

a. Remove two attaching screws and cover from 

contactor box.

b. Disconnect wires from reversing timer.

NOTE: Refer to wiring diagram when rewiring 
timer motor and switches.

c. Remove two screws holding reversing timer to 

back wall of contactor box.

d. Remove reversing timer.

65. REVERSING CONTACTOR

Refer to Figure 21.
a. Remove two attaching screws and cover from 

contactor box.

b. Disconnect wires from contactor coil terminals.

NOTE: Refer to wiring diagram when rewiring 
reversing contactor.

c. Remove screws holding reversing contactor to 

back wall of contactor box.

d. Remove reversing contactor.

66. FAN MOTOR CONTACTOR

Refer to Figure 21.
a. Remove two attaching screws and cover from 

contactor box.

b. Disconnect wires from contactor terminals.

NOTE: Refer to wiring diagram when rewiring fan 
motor contactor.

c. Remove two screws holding din rail to back 

wall of junction box.

d. Slide contactor off of din rail.

67. TRANSFORMER

Refer to Figure 21.
a. Remove attaching screws and cover from 

contactor box.

b. Disconnect leads from transformer terminals.

NOTE: Refer to wiring diagram when rewiring 
transformer.

c. Remove back guard.

d. Remove four screws and nuts holding 

transformer to back wall of contactor box.

e. Remove transformer.

Содержание D55



















































































Отзывы:

Нет отзывов