background image

STEP 1 - Set the time

  •  Use the up (     ) and 

    down (     ) arrow to set the  

    current time.

 

MODEL #TNIWP

STEP 2 - Pick a preset option

   •  Press one or more of the  

    preset options that meet your  

   needs.

   •  When the button lights up  

    the timer is set (timer must  

    be hardwired into an    

    electrical wall box for buttons  

    to illuminate).

   •  If you would like a custom  

    on/off time, move to Step 3.  

    If not, the setup of your new  

    EZ-SET timer is FINISHED!

STEP 3 - Set a Custom    

On/Off Time

   •  Hold down “Custom ON”  

    and press the up (

     

) and  

    down (

     

) arrow to set the  

    ON time.

 • Hold down “Custom OFF”  

    and press the up (

     

) and  

    down (

     

) arrow to set the  

    OFF time.

 • 

Press, BUT DO NOT 

    HOLD DOWN, the “Custom On” and “Custom Off” 

    buttons. Buttons will turn blue when the program 

    is activated.

EZ-SET DIGITAL

IN-WALL TIMER

IMPORTANT PRODUCT INFORMATION

INSTALLATION INSTRUCTIONS

PROGRAMMING INSTRUCTIONS

Single Pole:

 Timer will control devices from one location. 

Do not use in a 3-Way application where multiple switches 

control the same device.

Neutral Wire:

 Must be available as part of the wiring of 

the building. Timer will not function properly if a neutral 

wire is not available.

Direct Wire:

 This timer is only intended to be permanently 

installed into an electrical wall box.

Tool Required: 

One (1) standard flathead screwdriver.  

(not included)

1. Turn off power at circuit breaker or fuse box before  

  uninstalling existing device or installing new timer.

2. Remove existing wall plate and switch from wall box.

3. Make sure the following 3 wires are present in the wall  

  box. (see Diagram A)

  i.  1 Hot Wire from circuit breaker box

  ii.  1 Load Wire to the device to be powered

  iii. 1 Neutral Wire

  If one or more of these are not present, this timer will  

  not function properly.  Additional wiring to the wall box  

  will be required before installation of this timer can be  

 completed.

4. Strip wires 1/2 inch long. (see Diagram A)

5. Use the included wire nuts and securely twist together  

  to attach the timer wires to the building wires. (see   

  Diagram A) 

6. Insert timer into wall box (2-1/2 inch) being careful not to  

  pinch any wires.  Be sure timer is upright with LCD   

  screen located at the top of the timer. (see Diagram B)

7.  Fasten timer to the wall box using screws provided.   

  (see Diagram B)

8. Place rocker/decorator wall plate around the timer face.   

  (see Diagram B)

9. Restore power at circuit breaker or fuse box.

CUSTOM COUNTDOWN:

  •  Press “CTD”.  

 

  •  Press up (

      

) and down (

      

) arrow to set the    

    countdown from 1 minute to 24 hours.

    (Note: “CTD” will flash on LCD to indicate the    

    countdown feature is active)

 

MANUAL ON/OFF OVERRIDE:

  •  Press “On/Off” to bypass the current setting and turn  

    your device On or Off.

    (Note: Timer settings will resume based on the next  

    programmed cycle)

ADDITIONAL FEATURES

On to step 3

On to step 2

Diagram A

Diagram B

Hot Wire

Black Wire

White Wire

Load Wire

Neutral Wire

Ground Wire

Red Wire

Green Wire

From Timer 

In Wall Box

Black Wire 

Hot Wire

Red Wire 

Load Wire

White Wire 

Neutral Wire

Green Wire 

Ground Wire

*

*

or to ground post or screw terminal 

Custom

ON

Custom

OFF

5am-8am

5pm-8am

ON/OFF CTD

5pm-12am

Custom

ON

Custom

OFF

5am-8am

5pm-8am

ON/OFF CTD

5pm-12am

Custom

ON

Custom

OFF

5am-8am

5pm-8am

ON/OFF CTD

5pm-12am

Custom

ON

Custom

OFF

5am-8am

5pm-8am

ON/OFF CTD

5pm-12am

03-08292018

Call customer service at 1-888-445-9955,

8 a.m. - 5 p.m., PST, Monday - Friday.

Отзывы: