Each Box Contains:
1 Laser Light Projector
2 Piece Ground Stake (x2)
1 Remote Control (3V CR2032 Battery Included)
1 Remote Control Holder
2 Screws to mount Remote Control Holder
1 Instruction Manual
Required Tool:
Small Phillips Screwdriver (not included)
This product contains a built-in heater to protect the laser
diodes (light source) from freezing. The heater must
continue to receive power even when the light is turned off.
Failure to maintain the electrical power to this product when
temperatures drop below 32°F can cause permanent failure
of the laser diodes.
It may take up to 10 minutes after the laser has been turned
on for it to achieve full brightness.
SET-UP INSTRUCTIONS
PROGRAMMING INSTRUCTIONS
WARNING
Once plugged in, select your pattern and countdown time
and the Prime Laser Projector will automatically repeat
every day at dusk with your selected settings!
You may change settings on the laser with the remote
control or by using the buttons on the laser projector base.
A plastic stake is provided for in ground use.
KEY FEATURES
1.
Twist the 2 black stake parts together
clockwise to make one long stake.
(Fig. 1)
2.
Attach the long stake to the base of
the Laser Light Projector by twisting
clockwise. (Fig. 2)
3.
Push the stake into the ground
leaving the top half of the stake
(6 inches) exposed. Do not use
the laser unit itself to insert the stake
into the ground. (Fig. 3)
4.
Plug the unit into a GFCI protected
outlet.
5.
Use the angle adjustment knob
located between the head of the
Laser Light Projector and the base to
adjust the laser to the desired angle.
(Fig. 4)
6.
Remove clear plastic tab from the
battery compartment before use.
To replace the battery in the remote
control, use a small Phillips
screwdriver to remove the screw
that secures the battery compartment
cover on the back of the remote
control. The screw loosens by
turning it counterclockwise. (Fig. 5)
To open the plastic battery
compartment cover twist the battery
compartment cover counterclockwise with a coin or
other flat tool, aligning the arrow on the cover to the
UNLOCKED symbol, (Fig. 6). Remove the plastic cover
over the button cell battery to activate it or before
installing a replacement CR2032 button cell battery.
Make sure the negative side (-) of the battery faces
inward and the positive side (+) faces outward (Fig. 7).
Once the new battery is in place, align the arrow on the
cover with the UNLOCKED
symbol on the back of the
remote. Use a coin or other flat
tool to twist the battery
compartment cover to the right to
align with the LOCKED symbol.
To secure the battery
compartment place the small
screw back into the designated
hole in the battery compartment
and tighten it by turning it
clockwise. (Fig 8)
7. For easy access and storage of
the remote control, we’ve
included a holder that may be
wall-mounted. Mount the remote
control holder to a flat surface or
a wall and secure it with the two
screws that are included. (Fig 9)
Fig. 1
Fig. 2
Fig. 7
Fig. 4
Fig. 5
Fig. 6
Plug the laser into an outdoor rated
GFCI receptacle.
NOTE: When you first plug in the laser
• The default settings are:
• Light Color: Red & Green Mode
• Timer: 6 hours
• The laser light color may be
adjusted/set from either the top
button on the laser base labeled
“Mode” (Fig 10) or from the buttons
on the remote control.
• The time setting may be changed
either by pressing the bottom button
on the laser body labeled “Timer” or
from the buttons on the remote
control.
1. The laser will automatically turn on
at dusk each day and run for the
time programmed. It may take up to
10 minutes before the laser reaches
full brightness.
a.
IMPORTANT NOTE: Once you
have plugged in the laser to start
using it, do not unplug it until
done using it in that location.
2. There are 3 different color display
options to choose from: RED &
GREEN (default), GREEN ONLY or
RED ONLY.
a. RED & GREEN MODE
i. As mentioned, when the laser
is first plugged into an outlet,
this is the default setting.
ii. To select the RED & GREEN
color mode by using the
remote control, press the button to turn on the
laser. Press the R&G color mode button on the
remote control. Allow the laser to run through the
programmed timer setting or press the button
again to turn OFF the laser until it automatically
turns on at dusk.
iii. To manually select this mode, press the "Mode"
button on the base of the laser (Fig. 10) until the
laser projects red & green light. The laser must
run through a full timer cycle, (one night's use) for
the color mode you selected to be saved to repeat
the next night. The color mode will automatically
be saved even when the button on the remote
control is used to manually turn off the laser.
b. GREEN MODE
i. To select the GREEN color mode by using the
remote control, press the button to turn on the
laser. Press the G color mode button on the
remote control. Allow the laser to run through the
programmed timer setting or press the button
again to turn OFF the laser until it automatically
turns on at dusk.
Laser Light
Projector
Model#: CCLFLRGTR05
Item#: 1494311
ENGLISH FRONT-PAGE 1
©2015 Prime Wire & Cable, Inc. • City of Industry, CA 91789 • Service (888) 445-9955 • www.primewirecable.com
Fig. 3
ii. To manually select this mode,
press the "Mode" button on the
base of the laser (Fig. 10) until
the laser projects green light.
The laser must run through a
full timer cycle, (one night's
use) for the color mode you
selected to be saved to repeat
the next night. The color mode
will automatically be saved
even when the button on the
remote control is used to
manually turn off the laser.
c. RED MODE
i. To select the RED color mode
by using the remote control,
press the button to turn on
the laser. Press the R color
mode button on the remote
control. Allow the laser to run
through the programmed timer
setting or press the button
again to turn OFF the laser until
it automatically turns on at
dusk.
ii. To manually select this mode,
press the "Mode" button on the
base of the laser (Fig. 10) until
the laser projects red light.
The laser must run through a
full timer cycle, (one night's
use) for the color mode you
selected to be saved to repeat
the next night. The color mode
will automatically be saved
even when the button on the
remote control is used to
manually turn off the laser.
d. POWER OFF
i. To turn off the laser using the
remote control, press the
button. The laser will
automatically turn on again the
next evening at dusk in the last
color and timer modes.
ii. To turn off the laser manually,
press the “Mode” button until
the laser turns OFF. The laser
will automatically turn on again
the next evening at dusk in the
last color mode programmed.
3. There are 4 different timer settings to
choose from:
On at Dusk, off in 2, 4, 6 or 8 hours.
The default setting when the laser projector is first
plugged in is 6 hours.
a. To select the timer setting using the remote control,
first turn the laser ON by pressing the button.
b. Then press the 2h, 4h, 6h or 8h button to select how
long you want the laser to run each night. Press the
Fig. 8
Fig. 9
Fig. 10
2hrs
4hrs
6hrs
8hrs
