background image

Q550A

PNEUMATIC FLOORING TOOL

OPERATING INSTRUCTIONS

PNEUMATIC TOOL Q550A

The  pneumatic  nailer  Q550A  is  a  professional  tool
specially developed for the installation of 3/8" to 3/4" solid
and engineered hardwood flooring. It is designed for easy
maintenance where major components can be accessed
within seconds without the need of any tool.

The Q550A tool is offered in 2 different configurations:

• standard L-type 18

GA

 nails 

• combo nailer/stapler taking standard L-type 18

GA

 nails

or ¼" crown 18

GA

 staples 

Complete  documentation  specific  to  your  tool  can  be
retrieved by scanning the QR-Code applied on the tool.
You  will  find  updated  information  such  as  Operation
Manual,  Part  list,  Schematic  specifics  and  Technical
Notes specific to your tool as it was manufactured; as well
as useful information for ordering replacement parts.

Technical support, information &
schematics at

http://ts.primatech.ca/550

SAFETY MEASURES

These important guidelines should always be followed to
work safely with the Primatech pneumatic tool Q550A:

• Read these instructions thoroughly before using this tool

and keep it handy for reference if necessary.

• Always keep hands, feet or other body parts away from

the fastener ejection area.

• Never  aim  the  tool  in  any  direction  other  than  the

working area.

• Always carry or manipulate the tool by its handle while

the air supply hose is connected.

• Never hit the head cap of the actuator if the plastic base

is not sitting perfectly on the working surface.

• Never leave the tool laying down on its side while the air

supply hose is connected; the tool should always be left
on the floor, standing on its plastic base.

• Do not alter or remove safety.
• Always disconnect the air supply hose when the tool is

not in use or when move to another work area.

• Never service or repair  the tool, clear obstructions or

make  adjustments  while  the  air  supply  hose  is
connected.

• Only compressed air should be used to power this tool;

do not exceed 110 psi (7.6 bar).

• Never use oxygen or any other compressed gas as a

power source for this tool. Explosion may occur.

• Always wear OSHA-required Z-87 safety glasses with

side shields.

• Always wear proper ear and foot protection while the air

supply hose is connected.

• Always  remove  fasteners  from  the  magazine  before

servicing tool.

Do not remove or alter safety. Do not use a tool
with a defective safety. Never depress the
safety contact with your hands when tool is
connected to air supply. Extreme caution is
advised when using this tool.

Eye protection is recommended and should
be worn by the operator and other in working
area. Accidental ejection of fasteners or wood
debris could cause severe eye injury.

In some environments, ear  protection might
be required, as working condition may include
exposure to high  noise levels which lead to
hearing damage.

Wearing safety boots and safety hat is also
highly recommended.

Note: All the personal protection equipments
must meet national standards.

Содержание Q550A








Отзывы: