35
VOX
(long press)
The
VOX
function allows
transmitting
by speaking into the original micro-
phone (or in the optional vox microphone) without pressing the
PTT
switch
(
13
). The use of an optional vox microphone connected to the rear panel
of the transceiver (
E
)
disables
the original microphone.
Press shortly
VOX
key (
10
) in order to
activate
the
VOX
function.
“VOX”
appears on the display. Press shortly again the
VOX
key (
10
) to
disable
the
function.
“VOX”
disappears.
11) USB CHARGING SOCKET
The
USB
socket (
16
) can be used to charge smartphones, tablets or other
rechargeable devices with 5 V - 2.1 A.
12) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the
setting of the equipment into the dashboard easier.
See Cabling Diagram page 57.
13) PTT (Push To Talk)
Transmission key, press to
transmit
a message,
is displayed and release
to
listen to
an incoming communication,
disappears.
TOT (Time Out Timer)
If the
PTT
switch (
13
) key is pressed for more than 3 minutes, the display starts
blinking and the transmission
ends
. A beep will sound until the
PTT
switch
(
13
) key is released.
14) UP/DN BUTTONS ON MICROPHONE ~ SCAN
UP/DN BUTTONS ON MICROPHONE
(short press)
Press
UP
/
DN
buttons (
14
) on the microphone to
change
the channel.
UP
to
increase
and
DN
to
decrease
the channel.
See
ROTARY CH KNOB
page 33
.
SCAN
(very long press)
Press and hold the
UP
or
DN
button (
14
) for ± 7 seconds or until a beep
sounds to activate the
SCAN
function. The dot between the two channel
digits flashes to indicate that the function is active.
The scanning stops as soon as there is a busy channel. The scanning au-
tomatically starts 3 seconds after the end of the transmission and no key
is activated during 3 s. In
SCANNING
mode, turn the
F
rotary knob (
9
) or
press the
UP
/
DN
buttons (
14
) on the microphone to change scan direction.
Press
PTT
switch (
13
) to exit
SCAN
. The dot between the two channel digits
disappears from LCD.
A) DC-POWER TERMINAL (13,2 V / 26,4 V)
B) ANTENNA CONNECTOR (SO-239)
C) JACK FOR EXTERNAL OPTIONAL SPEAKER (8
Ω
, Ø 3.5 mm)
D) JACK FOR PA OPTIONAL SPEAKER (Public Address) (8
Ω
,
Ø 3.5 mm)
E) JACK FOR OPTIONAL VOX MICROPHONE (8
Ω
,Ø 2.5 mm)
C) FUNCTION TURNING ON THE UNIT
To
select
the
FREQUENCY BAND
turn
off
the unit. Press and hold the
F
key
(
9
) and then turn the unit
on
.
(
Configuration: EU; PL; d; EC; U; In
)
The frequency bands have to be chosen according to the country of use.
Don’t use any other configuration. Some countries need a user’s licence.
See table page 59
.
1.
Turn on the power while pressing the
F
key (
9
). The letter corresponding to
the current configuration is blinking.
2.
In order to change the configuration, use the rotary
CH
knob (
3
) on the unit
or the
UP
/
DN
buttons (
14
) on the microphone.
3.
When the configuration is selected, press the
F
key (
9
) during 1 second. The
letter corresponding to the configuration is continuously displayed and a
confirmation beep sounds.
4.
At this point, confirm the selection by switching off the transceiver and then
switching it on again.
See the frequency bands table at pages 54 to 56 / configuration table
page 58.
D) MENU
The order of 11 functions is as described in this manual. However, the func-
tion displayed by entering the
MENU
will be the last function modified by
user.
The procedure is the same Whatever the function is:
Press
F
knob (
9
) to
enter
MENU
. is displayed.
1.
Turn the rotary
CH
knob (
3
) or use
UP
/
DN
buttons (
14
) on the microphone
to
select
the menu.
English