Page 1
Installation Instructions
Installation Instructions
9531-000-091-00
Parts List
MM-EP15/28/42
(Varied sized pole with extrusion base)
(Qty 1)
The MM-EP15 is the 15” single pole
for multi-monitor mounts with base
for extrusion track installation. The
MM-EP28 is the 28” version, and the
MM-EP42 is the 42” version. These
three different pole sizes provide
more mounting options for those
installing multi-monitor mounts. The
larger the pole, the more displays
that can be mounted per single base.
This base is designed for extrusion
tracks typically used on consoles for
central stations and control centers.
The extrusion base fits standard
tracks and is a great mounting option
for upgrading from traditional CRT
monitors to HD flat-panel consoles.
Step 1
Multi-monitor mounts with extrusion track bases can be installed on 1.5” on
center T slot channel or single T slot channel (channel not included).
First, determine where you would like your multi-monitor mount positioned
on your desired surface. The mounting surface should be capable of
supporing 5x the weight of the flat-panel and mount. (Mount and flat-panel
sold separately)
Are you installing your pole on a 1.5” on center T slott channel?
If no, procede to step 2...
If yes, follow instructions below
Step 2
MM-EP15
MM-EP28
MM-EP42
T-Nut
(Qty 4)
1.
For dual 1.5” on center channel you will
need to use the four outer holes on the
base of the pole (Figure 1)
2.
Insert the four (4) 1/4 20” Flat Hex Screws
through the top of the four holes on base
shown in figure 1.
3.
Thread the four (4) provided T nuts onto
the bottom of each of the now installed
screws (Figure 3).
Do not thread all the way to the top.You
will need to leave loose for positioning the
tube on the extrusion track.
Procede to step 3.
Introduction
MM-EP15/28/42
1.
Once you have your Flat Hex Screws
installed and T-Nuts threaded in, insert
the base into the track.
2.
The bottom cable routing hole should
always be facing to the back.
3.
Slide pole to the desired position on the
track.
4.
Once in place, tighten the (4 for the dual
track and 2 for the single) 1/4 20” Flat
Hex Screws with the included hex key
so that the pole remains in place and is
sturdy (Figure 5).
5.
If the pole needs to be re-positioned on
the track, loosen the the flat hex screws
and simply slide to the new position.
Repeat sub-step 3 in this section.
15”
28”
42”
5/32” Hex Key
(Qty 1)
(Figure 1)
(Figure 2)
(Figure 4)
For single T slot channel you will need to use the two
center holes on the base of the pole (Figure 4).
Follow sub-steps 2 and 3 from the above section,
but only use two (2) 1/4 20” Flat Hex Screw and two
(2) T nuts into the holes noted in figure 4.
Procede to Step 3.
1/4-20” x 5/8” Flat Hex Screw
(Qty 4)
Bottom
View
(Figure 3)
Bottom
View
Step 3
Single T Slot Channel
1.5” on Center T Slott Channel
(Figure 5)
3100 E. Miraloma Avenue, Anaheim, CA 92806 | 800.368.9700 USA | F 800.832.4888 |
www.mounts.com
Unit 3, The Moorings Business Park, Channel Way | Longford, Conventry, CV6 6RH, UK |
+44 (0) 2476 644105 | F +44 (0) 2476 644165