Preference K-W6LCRSd Скачать руководство пользователя страница 1

page 1 of 4

Rev. A

page 4 of 4

Rev. A

INSTALLATION GUIDE

Frameless In-Wall LCR Loudspeaker

 

 

   

 

 

 

 

 

                       

Overall   

            Cut-Out (Round x Depth)

K-W6LCRSd  

    

6-1/2" In-Wall LCR Loudspeaker with Rotating Waveguide

                  

9" x 15-3/4"  

             7-15/16" x 14-7/16" x 3-1/2"

In-Wall model

Congratulations! 

 You have purchased a high quality stereo 

loudspeaker.  When matched to comparable electronic 
equipment, expect years of quality high fidelity sound.  Our 
belief is that music matters and we are focused on delivering 
superlative music reproduction everywhere in your home.

The following manual is designed to give you, the installer or 
owner, basic information as to the speaker’s installation and 
operation.  It is beyond the scope of this manual to go into all the 
details that must be taken into consideration in a sophisticated 
high fidelity system.  When installing the wiring and speakers it is 
important to adhere to all local codes and regulations.  Consulting 
a professional will help to maximize your system’s performance.  

If you have any questions that are not answered by this manual, 
contact your local dealer for assistance.  For the most current 
information please visit: www.preference-audio.com. 

SHIPPING DAMAGE

Each speaker is thoroughly tested before it leaves the factory.  
However, in shipment, accidents may occur.  Please inspect your 
speakers carefully when you receive them to make sure there 
is no damage.  If there is, please notify your dealer, or supplier 
immediately for assistance.  If you received your speakers by 
public transportation, report the damage at once to the shipping 
company.

AMPLIFIER OPERATION

These speakers will perform well with amplifiers from 5 to 125 
Watts RMS.  However, damage to the speakers can be done by 
amplifiers of nearly any power rating if the amplifier is overdriven 
into clipping.  “Amplifier clipping” is a phrase used to describe 
a condition when, because of the volume demand, an amplifier 
is being asked for more power than it can give.  Clipping causes 
distortion of the audio signal.  If you should hear an unusual 
amount of distortion at high listening levels then consider 
reducing the volume.  DAMAGE DONE TO A SPEAKER BY CLIPPING 
IS NOT COVERED UNDER THE WARRANTY.

HOW IS THIS SPEAkER DIFFERENT?

This speaker was designed and engineered to provide the finest 
performance achievable in a compact package.  The custom 
waveguide is unique in the industry and provides cross-axis 
performance that gives every listener in the room a sense of 
envelopment unmatched by other speakers in this category.  
By focusing the sound field across the listening space, the 
listener experiences a more balanced and symmetric sound level, 
especially when the main speakers are spaced more closely than 
is ideal, (common in many of today’s home theaters).  

The waveguide also increases the efficiency of the tweeter, 
allowing it to operate with far less input power and significantly 

lowering the distortion.  This also 
allows for the elimination of the 
ferro-fluid used for heat dissipation, 
improving elements of the tweeter’s 
performance including part-to-part 
consistency.  This same waveguide 
also allows the tweeter to operate a 
full octave lower than conventional 
dome tweeters while simultaneously 
reaching more than a half octave 
higher in frequency.  This allows the 
tweeter to cover more of the critical 
voice range. 

But we’re not done yet.  This same 
cross-axis tweeter design creates 
a much smoother off-axis listening 
experience, eliminating the midrange-
hole that is commonly experienced 
with conventional designs.  Additionally, by controlling the 
directivity of the sound field, the early reflections that occur from 
nearby walls and furniture are reduced so that more of the direct 
sound from the speakers are heard, improving the intelligibility 
and detail of the original sound source.   
 
Finally, the inset tweeter produces a time aligned position and 
excellent phase coherency with the woofer, improving the off-axis 
performance, both in the vertical and horizontal directions. 
 

WOOFER

While the tweeter has allowed us to create a truly unique speaker, 
the woofer’s complement of components provides the balance of 
performance. Every detail of the woofer was considered using a 
“Design of Experiments” methodology:  

• 

Cast aluminum basket with its stiff but inert structure

• 

Super-light extra-long copper-clad aluminum voice coil

• 

Low eddy-loss mechanically damped Kapton former

• 

Lightweight curved woven cone made from genuine Dupont Kevlar

®

• 

Linear-transitioning butyl rubber surround

• 

Vibration damping silica rubber motor boot

• 

High compliance flat spider

• 

Machined aluminum heat-dissipating phase plug

Clearly, care was exercised to create a woofer that behaves as well 
off-axis as it does on-axis and meets the tweeter’s top caliber 
performance.  

CROSSOvER

Of course all of this performance is brought together using a 
sophisticated multi-order crossover that seamlessly blends the 
drivers for performance that rivals and exceeds everything in 
its class.  The crossover contains two level controls to tailor the 
speaker for the application.  

CONTROL ADjuSTMENT  

There are 2 switches located on the front baffle, labeled MF and 
HF, (Mid-Frequency and High-Frequency, respectively).  Each 
switch has 3 positions that allow the user to tailor the sound of 
the speaker for different room acoustics, mounting locations, 
and personal preference.  These controls are also useful when 
using the speakers behind acoustically transparent video screens 
(where some augmentation of the upper frequencies may be 
necessary) or when customizing the speakers for unique surround 
applications where the sound may be either focused directly at 
the seating area or reflected off nearby surfaces.  The diagrams 
below show an approximation of how each control affects the 
frequency response.  Moving the switches up () increases 
the output.

The Mid-Frequency (MF) control allows for a relaxed, neutral, or 
forward midrange presence.  

The High-Frequency (HF) control affects the uppermost audible 
range to create soft, neutral, or articulate detail. 

PAINTING THE GRILLE

The grilles can be painted using multiple light coats of spray paint.  
Custom color spray paints are available from specialty companies.  
Contact your dealer for more information.  The grilles should be 
removed from the speaker and painted in a clean environment to 
prevent contamination.  It is best to go around the grilles and apply 
the paint from multiple angles.  DO NOT remove the scrim cloth 
from the backside of the grille.  It is not replaceable. 

Attach the grilles to the speakers and enjoy.  Should you wish 
to remove the grilles from the speakers pull at the grilles' edge.  
Initially there will be significant resistance because the grilles are 
magnetically attached.

+

-

SP

(O

ut

pu

t i

dB

)

Frequency (Hz)

+

-

SP

(O

ut

pu

t i

dB

)

Frequency (Hz)

www.preference-audio.com

[email protected]

(775) 355-0405

(800) 291-0561 FAX

K-W6LCRSd

- Front Channel

- Center Channel

- Side Channel

D

 - Rear Channel

- Subwoofer

- 2 Channel Ambient

SuGGESTED SPEAkER LAyOuT OPTIONS

Отзывы: