background image

Page 14

For technical questions, please call 1-888-866-5797.

ITEM 69727 

        

S

AFETY

S

ETU

p

Op
ERA

TION

M

AINTENANCE

Air Filter Maintenance

1.  Remove the Air Cleaner Cover and the air filter(s) 

and check for dirt. Clean as described below.

2. 

Cleaning:

•  For paper filters: 

To prevent injury from dust and debris, 
wear ANSI-approved safety goggles, 
NIOSH-approved dust mask/respirator, and 
heavy-duty work gloves.  In a well-ventilated 
area away from bystanders, use pressurized 
air to blow dust out of the filter.

•  For foam filters: 

Wash the filter in warm water and mild 
detergent several times. Rinse. Squeeze out 
excess water and allow it to dry completely.  
Soak the filter in lightweight oil briefly, 
then squeeze out the excess oil.

3.  Install the cleaned filter(s).  Secure the 

Air Cleaner Cover before use.

Spark plug Maintenance

1. 

Spark 

plug 

Cap

Disconnect spark plug cap from end of plug.  
Clean out debris from around spark plug.

2. 

Using a spark plug wrench, remove the spark plug.

3.  Inspect the spark plug: 

If the electrode is oily, clean it using a clean, dry rag.  
If the electrode has deposits on it, polish it using 
emery paper. If the white insulator is cracked or 
chipped, the spark plug needs to be replaced.

Recommended Spark plugs

NGK

®

BP-6ES

NHSP

® / 

TORCH

®

F6TC

NOTICE:

 Using an incorrect spark plug 

may damage the engine.
4.  When installing a new spark plug, 

adjust the plug’s gap to the specification on the 
Specifications chart.  Do not pry against the 
electrode, the spark plug can be damaged.

5.  Install the new spark plug or 

the cleaned spark plug into the engine.
• 

Gasket-style

:   

Finger-tighten until the gasket 
contacts the cylinder head, 
then tighten about 1/2-2/3 turn more.

• 

Non-gasket-style

:  

Finger-tighten until the plug 
contacts the cylinder head,  
then tighten about 1/16 turn more.

NOTICE:

 Tighten the spark plug properly.   

If loose

, the spark plug will cause the 

engine to overheat.   

If overtightened

, the threads in the 

engine block will be damaged.
6.  Apply dielectric spark plug boot protector 

(not included) to the end of the spark plug 
and reattach the cap securely.

Содержание 61563

























Отзывы: