PRECITEC Lasermatic LightCutter Скачать руководство пользователя

Страница: 41 / 82

3 Fitting and installing

D 159195

3 - 31

3.4

Installation

3.4.1

Connecting the cutting gas system

(trained personnel only)

Fig. 3-7

Installation: Connections - Cutting gas

Cutting gas

Attention – Pressure tightness!

Please ensure that all connections on the laser head that are not being used
are closed with screw plugs; otherwise the laser head will no longer work
correctly and gas or liquids can get into it.

LC-

BA-

G1/8

(8 mm deep)

Cutting gas, G 1/8 connection

Attention – Cutting gas!

Only clean, dry cutting gas can be used.

Cutting gas quality in compliance with ISO 8573-1:2010; Solid particles - Class 2,
Water - Class 4, Oil - Class 3 (see

Tab. 8-2

, page

8-65

The maximum pressure on the laser head is 25 bar

(2.5 MPa)



Connect the cutting gas hose to connection (1)

(G1/8, 8 mm deep)

Precitec recommends connecting the cutting gas using hoses with the largest possible

diameter.

When delivered, the connections are closed with dummy plugs.

Attention:

Sealing the fittings - sealing tape or sealing material is not permitted!

Содержание Lasermatic LightCutter



















































































Результаты поиска

Содержание Lasermatic LightCutter

Отзывы:

Похожие инструкции для Lasermatic LightCutter

Бренды по названию

Популярные бренды

PRECITEC Lasermatic LightCutter, Руководство по эксплуатации

Результаты поиска

Содержание Lasermatic LightCutter

Отзывы:

Похожие инструкции для Lasermatic LightCutter

Бренды по названию

Популярные бренды