PRECISION DIGITAL PD2-6210 Скачать руководство пользователя страница 24

Страница: 24 / 60

Helios Large Display Analog Input Batch Controller Instruction Manual

PD2-6210

MeterView

Pro Software

The meter can also be programmed using the PC-based MeterView Pro software included with the meter.

This software is can be installed on any Microsoft® Windows® (2000/XP/Vista/7/8/10) computer by

connecting the meter’s onboard USB. The meter is powered by the USB connection, so there is no need

to wire anything prior to programming the meter, though USB is intended only for meter configuration.

MeterView Pro Installation

1. Connect one end of the provided USB cable to the meter and the other end to the computer. The

computer will automatically install the driver software it needs to talk to the meter.

Only one meter may be connected at a time. Attaching multiple meters will cause a conflict

with the meter software. Disconnect other meters before performing these steps.

2. Once the driver is installed, an AutoPlay dialog should appear

for the drive “MAINSTAL.” Click “Open folder to view files.”

If the computer does not display an AutoPlay dialog for the

drive “MAINSTAL,” you should open My Computer and double-

click on the drive labeled “MAINSTAL.”

3. Double-click on the file named “MAStart.” The program will

open a few windows and install two programs on your

computer. Simply follow the onscreen instructions until you see

one of the dialogs below. If you receive a “User Account

Control” warning, click “Yes.”

4. If there is an update available, click the “Update” button to

install the new version. Otherwise, click “Configure” to begin

programming your meter.

Note:

If you decide to update your MeterView Pro software, once the installation has completed, you

will be asked if you want to update the setup files located on the meter itself. This way, you will always

have the most current version on the meter for future installs.

Warning

Do not unplug the meter while the new installation files are being written to it. The

meter will display

uwrite

during the process and you will receive an onscreen

notification once the process is complete.

Data logging for one meter at a time is available with MeterView Pro software. More advanced data

acquisition may be accomplished by using any Modbus RTU compliant software. Additional information

regarding configuration and monitoring of the meter using MeterView Pro software is available online.

Front Door

Panel

MENU

RESET

MAX

ENTER

www.calcert.com

[email protected]

1.888.610.7664

Содержание PD2-6210





























































Результаты поиска

Содержание PD2-6210

Отзывы:

Похожие инструкции для PD2-6210

Бренды по названию

Популярные бренды

PRECISION DIGITAL PD2-6210, Инструкция по эксплуатации

Результаты поиска

Содержание PD2-6210

Отзывы:

Похожие инструкции для PD2-6210

Бренды по названию

Популярные бренды