Precision Digital Corporation PD6622-L2N Скачать руководство пользователя страница 19

Страница: 19 / 45

Loop Leader PD6620 Series Loop-Powered Flow Rate/Totalizers

Instruction Manual

Main Menu

The main menu consists of all the meter’s program-

mable functions:

Input

Output, Advanced,

and

Dis-

play

•

Press

Menu

button to enter

Programming Mode

then press the

Right-Arrow

button to move for-

ward through the menu and the

Up-Arrow

button

to move back.

•

Press

Menu

at any time to go back one level or

press & hold to exit and return to

Run Mode

Changes made to settings prior to pressing

Enter

are not saved.

•

Changes to the settings are saved to memory

only after pressing

Enter/F3

to confirm the set-

ting or pressing

Enter/F3

at the

SAVE?

screen

when available.

Note:

The

BARGRAPH

menu appears in the PD6624/8

menu only.

Setting Numeric Values

The numeric values are set using the

Right

and

Up-Arrow

buttons.

1. Press

Right

Arrow

to select next digit and

Arrow

to increment digit value. The

selected digit will flash.

2. Press and hold

Arrow

to auto-increment

the display value. If you have made a

mistake or would like to enter a new value,

select the left-most digit and press and hold

the

Right

Arrow

button until all digits reset

to zero.

3. Press the

Enter

button at any time to accept

a setting or

Menu

button to exit without

saving changes.

Note:

the underscore in the graphic below is provided

to show which digit would be flashing.

Scaling the 4-20 mA Input (

INPUT

)

It is

very important

to read the following information

before proceeding to program the meter:

•

The meter is factory calibrated prior to shipment

to display 0.00 to 100.00 gal/s, which corre-

sponds to the 4-20 mA input. The calibration

equipment is traceable to NIST standards.

•

A calibrated signal source is not needed to scale

the meter.

Enter the

Input

menu to scale the meter to display the

4-20 mA input. The input can accept any signal from

4 to 20 mA.

DSP 1

+00,000.00

DSP 1

00,000.00

Select

Digit to

Change

DSP 1

00,050.00

Increment

Selected

Digit

SCALE

INPUT 2

Setting

SETUP

INPUT

SCALE

UNITS

SCALE

INPUT 1

SCALE

DISP 1

TIME

/SECOND

UNIT

GAL/S

/SECOND
/MINUTE
/HOUR
/DAY

Rate Time

Bases

INP 1

04.000

INP 1

Flashes Units

Momentarily

DSP 1

+00,000.00

SCALE

INPUT 2

INP 2

20.000

SCALE

DISP 2

DSP 2

+00,100.00

SAVE?

SETUP

INPUT

GAL/

(T)

IGAL/

(T)

Rate Units

M3/

(T)

BBL/

(T)

BUSH/

(T)

cuYD/

(T)

cuFt/

(T)

cuIn/

(T)

LiBBL/

(T)

BBBL/

(T)

HECtL/

(T)

AF/

(T)

CUSTM/

(T)

52.86

38,418.2

SETUP

INPUT

SETUP

OUTPUT

SETUP

ADVANCED

SETUP

DISPLAY

OPEN

COLLECTR

ADV

RATE

DSPLY

UNITS

OUT

RELAY

OUT

4-20 mA

OUT

CONTROL

CUTOFF

FILTER

PASSWRD

USER

SYSTEM

DSPLY

DEC.PT

DSPLY

COMMA

DSPLY

TOP

DSPLY

DOTTOM

SCALE

UNITS

SCALE

INPUT 1

SCALE

DISP 1

SCALE

INPUT 2

SCALE

DISP 2

SAVE?

ADV

TOTAL

ADV

GTOTAL

Run Mode

DSPLY

BARGRAPH

*PD6624/8

Only

Содержание PD6622-L2N














































Результаты поиска

Содержание PD6622-L2N

Отзывы:

Похожие инструкции для PD6622-L2N

Бренды по названию

Популярные бренды

Precision Digital Corporation PD6622-L2N, Инструкция по эксплуатации

Результаты поиска

Содержание PD6622-L2N

Отзывы:

Похожие инструкции для PD6622-L2N

Бренды по названию

Популярные бренды