Praxair PHOENIX 401 BASIC PULS forceArc Скачать руководство пользователя

Страница: 47 / 60

Functional characteristics

TIG welding

Item No.: 099-004838-PRA01

5.3.2.5

Latched special

END

START

Figure 5-20

Selection

• Select latched special mode

Step 1
• Press and hold torch trigger.
• Shielding gas is expelled (gas pre-flows).

The arc is ignited using liftarc.
• Welding gas flows at pre-selected setting in start program "P

START

Step 2
• Release torch trigger.
• Slope on main program "P

The slope on main program P

is given at the earliest after the set time t

START

elapses and at the

latest when the torch trigger is released.

Tapping can be used to switch to the reduced main program "P

". Repeated tapping will switch

back to the main program "P

Step 3
• Press the torch trigger.
• Slope to end program "P

END

Step 4
•  Release torch trigger.
•  Arc is extinguished.
•  Gas post-flow time elapses.

5.3.3

TIG automatic cut-out

If the arc does not ignite after starting or if the arc is interrupted when the torch is moved away,
an automatic cut-out occurs after 5 sec. The gas and

open circuit voltage

(power unit) are

switched off.

Содержание PHOENIX 401 BASIC PULS forceArc





























































Результаты поиска

Содержание PHOENIX 401 BASIC PULS forceArc

Отзывы:

Похожие инструкции для PHOENIX 401 BASIC PULS forceArc

Бренды по названию

Популярные бренды

Praxair PHOENIX 401 BASIC PULS forceArc, Руководство по эксплуатации

Результаты поиска

Содержание PHOENIX 401 BASIC PULS forceArc

Отзывы:

Похожие инструкции для PHOENIX 401 BASIC PULS forceArc

Бренды по названию

Популярные бренды