Praxair PHOENIX 401 BASIC PULS forceArc Скачать руководство пользователя | Manualshive

Страница: 43 / 60

background image

Functional characteristics

TIG welding

Item No.: 099-004838-PRA01

43

5.2.7

Interfaces

Only the accessory components described in these operating instructions may be connected.

Only plug accessory components into the relevant connection socket on the welding machine
and lock it when the machine is switched off. The component is detected automatically when the
welding machine is switched on.

Comprehensive descriptions can be found in the operating instructions for the relevant
accessory components.

5.2.7.1

PC interfaces

PC 300 welding parameter software
Create all welding parameters quickly on the PC and easily transfer them to one or more welding
machines (accessories: set software, interface, connection leads)

Q-DOC 9000 welding data documentation software
(Accessories: set with software, interface, connection leads)

The ideal tool for welding data documentation of, for example:
Welding voltage and current, wire speed and armature current

WELDQAS welding data monitoring and documentation system
Network-compatible welding data monitoring and documentation system for the digital Phoenix and Tetrix
machines

5.3

TIG welding

5.3.1

TIG arc ignition

5.3.1.1

Liftarc

Figure 5-16

The arc is ignited on contact with the workpiece:
a) Carefully place the torch gas nozzle and tungsten electrode tip onto the workpiece and press the torch

trigger (liftarc current flowing, regardless of the main current set).

b) Incline the torch over the torch gas nozzle to produce a gap of approx. 2-3 mm between the electrode

tip and the workpiece. The arc ignites and the welding current is increased, depending on the
operating mode set, to the ignition or main current set.

c) Lift off the torch and swivel to the normal position.

Ending the welding process: Release or press the torch trigger depending on the operating mode
selected.

«
...
41
42
43
44
45
...
»

Содержание PHOENIX 401 BASIC PULS forceArc





























































Отзывы:

Нет отзывов

Похожие инструкции для PHOENIX 401 BASIC PULS forceArc

Бренд: Zazen Страницы: 8

Бренд: ATD Tools Страницы: 24

Vizzyalarm VZW-02

Бренд: Alderon Industries Страницы: 6

Бренд: Nice Страницы: 12

Бренд: Q Acoustics Страницы: 32

RIS 700HE/HW EKO 3.0

Бренд: Salda Страницы: 40

Бренд: Onkyo Страницы: 8

Бренд: Tractel Страницы: 162

Бренд: Thermal Dynamics Страницы: 40

Бренд: EAW Страницы: 2

Бренд: TBM Страницы: 21

Бренд: UltraSecure Страницы: 2

Бренд: Belson Страницы: 34

Бренд: Lifter Страницы: 170

Genesis Chime-Strobe Series

Бренд: Edwards Страницы: 4

Бренд: Thermal Dynamics Страницы: 32

Бренд: Parweld Страницы: 20

Бренд: olympia electronics Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды