DETECTION RANGE
The figures below show the sensor detection range viewed from above and from the side.
SMART PET, SMART PET PRO, SMART DIGITAL:
The maximum coverage angle is 110° and the reach is 14 m when
installed at 2.4 m high and 90° from the ground.
SMART SOLID, SMART SOLID PET:
The maximum coverage angle is 110° and the reach is 12 m when
installed at 2.4 m high and 90° from the ground.
GENERAL TERMS AND CONDITIONS OF WARRANTY
MOTOPPAR, Industry and Commerce of Automatic Gate Operators Ltd., registered with the CNPJ (National Registry of Legal
Entities) under Number 52.605.821/0001-55, located at 3526 Dr. Labieno da Costa Machado Avenue, Industrial District, Garça – SP
– Brazil, Zip Code 17400-000, manufacturer of PPA Products, hereby guarantees this product against design, manufacturing or
assembly defects and/or supportively as a result of material quality flaws that could make its intended use improper or inadequate,
within a legal period of ninety days from time of acquisition, provided that the installation instructions described in the instruction
manual are observed.
Due to the credibility and trust placed on PPA products, we will add 275 more days to the period mentioned above, reaching
a warranty period of one year, likewise counted from the time of acquisition proven by consumer through proof of purchase
(Customer Receipt).
In case of defect, within the warranty period, PPA responsibilities are restricted to the repair or substitution of the product
manufactured by the company, under the following conditions:
1. Repair and readjustment of equipment may only be carried out by PPA Technical Assistance, which is qualified to open, remove,
and substitute parts or components, as well as repair defects covered by this warranty; thus, failure on observing this guideline
and the verified use of any non-original parts will cause the resignation of this warranty on the part of the user;
2. The warranty will not extend to accessories such as cables, screw kit, fixing brackets, power supplies etc.;
3. Expenses for packaging, transportation and product reinstallation will be sole responsibility of the consumer;
4. The equipment must be sent directly to the Company responsible for the sale (manufacturer's representative), through the
address contained in the purchase invoice, properly packed, thus avoiding loss of the warranty;
5. Within the additional period of 275 days, visits and transportation in places where authorized technical assistance is not available
will be charged. The cost of transportation of the product and/or technician will be sole responsibility of the consumer and
6. The substitution or repair of the product does not prolong the warranty time.
This warranty will be terminated if the product:
1. Is damaged by natural agents, such as atmospheric discharges, floods, wildfires, landslides etc.;
2. Is installed in an improper electric power supply or if it is not according to any of the installation instructions displayed on
the manual;
3. Shows defects caused by droppings, collisions or any other physical accident;
4. Shows signs of product violation or attempted repair by unauthorized personnel;
5. Is not used for its intended purpose;
6. Is not used under normal conditions;
7. Is damaged by accessories or equipment connected to it.
Recommendation:
We recommend that both the installation and the maintenance of the operator to be performed by an authorized PPA technical
service. If the product fails or has an improper operation, seek an Authorized Technical Service to fix it.
SENSORS
SMART PET PRO, SMART DIGITAL,
SMART PET, SMART SOLID AND
SMART SOLID PET
INSTRUCTION MANUAL
P30654 - 04/2022
Rev. 0
ATTENTION:
Do not use the equipment
without first reading the
instruction manual.
Made by:
Motoppar da Amazônia Indústria e Comercio de Eletrônicos LTDA
Praça Linear, 100, Bloco 2 - Centro - Santa Rita do Sapucaí - MG - CEP 37540-000 - Brasil
CNPJ: 09.084.119/0002-45
www.ppa.com.br | +55 14 3407 1000
TECHNICAL CHARACTERISTICS
SMART PET PRO
SMART DIGITAL
SMART PET
SMART SOLID
SMART SOLID PET
Double
pyroelectric
element
Yes
Yes
Yes
Yes
Yes
Detection
14m reach x
110° opening
14m reach x
110° opening
14m reach x
110° opening
12m reach x
110° opening
12m reach x
110° opening
Activation time
2 seconds
2 seconds
2 seconds
2 seconds
2 seconds
Stabilization
time
60 seconds
60 seconds
60 seconds
60 seconds
60 seconds
RF protection
25V/m up to
1GHz
25V/m up to
1GHz
25V/m up to
1GHz
-
-
Supply voltage
9~18 V DC
10 ~ 15 V DC
10 ~ 15 V DC
10 ~ 18 V DC
10 ~ 18 V DC
Consumption
5mA @ 12 V DC 20 mA (12 V)
20 mA (12 V)
15 mA (12 V)
15 mA (12 V)
Temperature
compensation
-10° a 45°
-10° a 45°
-10° a 45°
-10° a 45°
-10° a 45°
SENSOR DIMENSIONS
NOTE:
All dimensions are in millimeters.
PRECAUTIONS
- Do not touch the pyroelectric element of the sensor;
- Avoid possible sources of false alarms in the sensor detection area (e.g. animals, air
conditioners, etc.);
- Avoid direct white light to the sensor;
- Fix the sensor on solid walls that do not suffer vibrations;
- Do not pass the sensor cables along the electrical network wiring;
- Avoid obstacles in the sensor detection area.
- Do not install the sensor in open areas.
TAMPER FUNCTION (SMART DIGITAL, SMART PET)
The TAMPER Function makes it possible to send information to the alarm center in case
of violation/opening of the plastic box.
PET FUNCTION (SMART PET PRO, SMART PET, SMART SOLID PET)
Immune to creeping animals up to 20kg (~44lb).
10
5
36
68
105
10
5
36
68
68
36
MAIN COMPONENTS OF THE BOARD
The following figures illustrate the sensor boards with their components:
SMART PET PRO
SMART DIGITAL, SMART PET
Pyroelectric element
(detector).
J1:
Sets one of three
detection sensitivity
levels (low, medium
or high).
NOTE:
The
adjustment must be
done with the sensor off
(no power), otherwise
the changes will not
take effect.
J3:
Configures the
sensor to operate in
NO (normally open)
or NC (normally
closed) mode.
NOTE:
the vast
majority of alarm
panels, currently
available, use the NC
mode.
J2:
Enables and
disables the
LED.
Detection
indication LED
ATTENTION!
-Avoid touching the sensor window.
-For cleaning use only ethyl alcohol
with a cotton swab when necessary.
-Do not touch the sensor without
ESD protections, in order to avoid
electrostatic discharges.
NO RESISTOR:
Normally open
alarm output (NO)
when detection
occurs the output
closes.
WITH RESISTOR:
Normally closed
alarm output (NC)
when detection
occurs the output
opens.
WITH RESISTOR:
LED on
WITHOUT
RESISTOR: LED off
Alarm output
Input power;
9~18 VDC
Signaling LED
ADJUSTMENT
OF SENSITIVITY
MIN: Lower
sensitivity
MAX: Highest
sensitivity
NOTE:
Before
changing the
resistor status,
turn off the sensor
power.
SMART SOLID,
SMART SOLID PET
J2:
Enables and
disables the LED.
Detection indication
LED
Pulse 1 - Adjusts
the maximum
sensitivity of the
sensor
Pulse 3 - Adjusts
the minimum
sensitivity of the
sensor
Vertical
adjustment of
detection range
(see below)
ATTENTION!
The recommended height
for mounting the sensor is
2.1 to 2.4 m.
In order for the pet function
of the SMART SOLID PET
and SMART PET PRO sensor
models to work correctly,
do not use articulators or
install the sensor inclined
downwards. They must be
fixed at 90º in relation to the
floor.
Sensor piroelétrico