background image

 

22 

• Misaligned tension pulley, the pulley should move parallel to the belt centered to the belt 
• Check return spring operation and tension 
 

Inspect the auger control lever (handle) and cable: 

• Cable and connection damage 
• Free movement (from engage to disengaged positions) 
• Binding or improperly routed cable 
• Cable pulley(s) damage, misalignment and binding 
• Cable adjustment plate damaged or improper installation 
• Handle damaged or binding at pivot 
 

STORAGE & CLEANING 

 

PROPER STORAGE PROCEDURES 
WARNING!

 Never store your snow shrower for extended periods of time with fuel in the tank or 

carburetor. Fuel stabilizer can be added to the fuel in can to extend its shelf life for storage. 
 
Store the unit in a locked, dry place out of the reach of children to prevent unauthorized use or damage. 
Cover loosely with a tarp for added protection. 
 

CLEANING 

1.

 

To clean your Snow Thrower, use a damp cloth and mild detergent on the surfaces only. Never get 
soap or water inside the working mechanisms of your Snow Thrower. 

 
Note:

 Do not clean with water. Water will freeze due to low temperature and damage the machine. 

 
2.

 

Clean the Snow Thrower of snow and ice buildup before storing or transporting. Be sure to secure the 
unit while transporting. 

3.

 

Inspect the Snow Thrower carefully for worn, loose, or damaged parts. Check connections and 
screws and tighten if necessary. 

Содержание DB7651SL

































Отзывы: