background image

 

16 

AUGER AND DRIVE CONTROLS 

1. To engage the auger (blades), press down on the auger control lever (left side handle).
2. To engage the drive, press down on the drive control lever (right side handle). The machine should

start moving in the direction and speed for the respective setting on the speed/gear control.

3. When finished clearing a snow path, release the auger control lever (handle) and the drive control

lever (handle).

Attention:

Release (disengage) the auger and drive control lever (handles) before adjusting the drive 

speed control lever. 

NEVER change the drive/gear speed while your snow thrower is  in motion, as it will

 

damage the drive mechanism and void the warranty.

 

 
DRIVE SPEED/GEAR CONTROL 

Move the drive speed control lever to the desired speed. There are eight 
(8) settings: six (6) forward speeds and two (2) reverse speeds.

 

1 is the slowest forward speed and 6 is the fastest forward speed.
R1 is the slowest reverse speed and R2 is the fastest reverse speed.

Note: There is no neutral drive setting since the drive control 
handle must be engaged for movement. Neutral is achieved when 
the drive control handle is disengaged. 

CHUTE DISCHARGE DIRECTION ADJUSTMENT 

WARNING

 - Never direct the snow discharge chute at the operator, bystanders, vehicles or 

nearby windows. Discharged snow and foreign objects accidentally picked up by the Snow 
Thrower can cause serious damage and severe bodily injury. Always point the discharge 

chute in the opposite direction from potential hazards. The discharge chute can be adjusted 180º by 
rotating the chute rotation handle. Rotate the chute rotation handle clockwise to move the discharge chute 
to the left; counterclockwise to move the chute to the right. 

Auger Control     
Lever (Handle) 

Drive Control 
Lever (Handle) 

Содержание DB7127




































Отзывы: