background image

SNOW THROWER PREPARATION

ADD OIL

The snow thrower is shipped without oil. User must add the proper amount of oil before operating the 
snow blower for the first time. The oil capacity of the engine crankcase is 20 fl. oz. For general use, we 
recommend 5W, 4-stroke engine oil.

ENGINE OIL RECOMMENDATIONS

Select good quality detergent oil bearing the American Petroleum Institute (API) service classifications 
SJ, SL, or SM (synthetic oils may be used). Use the ASE viscosity grade of oil from the following chart 
that matches the starting temperature anticipated before the next oil changes.

To add oil, follow these steps:
1. Make sure the snow thrower is on a level surface. Tilting the snow 

thrower to assist in filling will cause oil to flow into engine areas 
and will cause damage. Keep snow thrower level!

2. Remove the dipstick from the engine. 
3. Add oil slowly as to not overflow the unit.
4. To check the oil level, wipe the dipstick with a clean rag. Insert the 

dipstick into the oil fill opening without screwing it in. Remove the 
dipstick to check the oil mark.

5. Slowly add more oil and repeat step 4 until the oil mark reaches to 

the top of the dipstick. Do not overfill the crankcase. 

6. Check for oil leaks. Tighten dipstick firmly.

ADD GASOLINE

Use fresh (within 30 days from purchase), lead-free gasoline with a minimum of 87 octane rating. Do not 
mix oil with gasoline.
To add gasoline, follow these steps:
1. Make sure the snow thrower is on a level surface.
2. Unscrew fuel tank cap and set aside. NOTE: The fuel cap may be tight and hard to unscrew.
3. Slowly add unleaded gasoline to the fuel tank. Be careful not to overfill. The capacity of the fuel tank 

is 0.66 gallons. NOTE: Do not fill the fuel tank to the very top. Gasoline will expand and spill over 
during use even with the fuel cap in place.

4. Reinstall fuel cap and wipe clean any spilled gasoline with a dry cloth.

IMPORTANT:

Never use an oil/gasoline mixture.

Never use old gasoline.

Avoid getting dirt or water into the fuel tank.

Gasoline can age in the tank and make starting difficult. Never store snow thrower for extended 
periods of time with fuel in the tank or the carburetor.

NOTE:

After completing the above preparation, the engine is ready to be started.

14

Содержание DB7004



































Отзывы: