background image

 

POWX180 

EN

 

Copyright © 2019 VARO 

P a g e

 | 

11

 

www.varo.com 

9.4 

Making double mitre cuts (Fig. 31) 

Angled cutting of a workpiece. 

 

Undo the securing screw (8) and the locking handle (9) under the saw bench (6). 

 

Tip the saw bench (6) towards the outside until you reach the angle you require. 

 

Tighten the locking handle (9) and securing screw (8) again. 

 

Push the lateral stop (29) into one of the two grooves on the saw bench (6) and set the 
required angle on the scale on the lateral stop (29). 

 

Lower the saw band guide (22) as far as possible on to the workpiece. 

 

Switch on the bandsaw. 

 

Press the workpiece firmly against the lateral stop (29) with your right hand. Press the 
workpiece flat on to the saw bench (6) with your other hand. 

 

Now Slide the workpiece against the saw band (14) at a uniform feed speed. 

9.5 

Making free-hand cuts (Fig. 32) 

The  most  outstanding  feature  of  a  bandsaw  is  its  facility  that  enables  you  to  complete  free-
hand cuts. 

 

Lower the saw band guide (22) as far as possible on to the workpiece. 

 

Switch on the bandsaw. 

 

Press the workpiece flat on the saw bench (6) and slide it slowly up to the saw band (14). 

 

Use a low feed speed for all free-Hand cuts since this will enable you to follow the required 
line more easily. 

 

in some cases you may have to make a coarse cut approximately 5 

– 10 mm away from 

the actual cutting line. 

 

If the curve you wish to cut is too tight for the saw band (14) you are using, you must first 
make auxiliary cuts up to the front edge of the curve so that these pieces of wood will fall 
away when you have sawn the final radius. 

10 MAINTENANCE AND CARE 

Attention  !    Before  performing  any  work  on  the  equipment,  pull  the  power 
plug. 

10.1 

Cleaning 

 

Keep the ventilation slots of the machine clean to prevent overheating of the engine. 

 

Regularly clean the machine housing with a soft cloth, preferably after each use. 

 

Keep the ventilation slots free from dust and dirt. 

 

If the dirt does not come off use a soft cloth moistened with soapy water. 

Never  use  solvents  such  as  petrol,  alcohol,  ammonia  water,  etc.  These 
solvents may damage the plastic parts. 

10.2 

Lubrication 

Oil the saw band guides (19) (20) (21) (top and bottom) at regular intervals.. 

 

 

Содержание POWX180















Отзывы: