background image

 

POWX093 

EN

 

Copyright © 2015 VARO 

P a g e

 | 

8

 

www.varo.com 

7.5 

Inserting and removing the chuck and cutting heads n 

 

The  cutting  machine  is  supplied  with  a  set  of  12  mm  cutting 
heads.  There  are  a  number  of  heads  for  cutting  various 
profiles  in  wood.  One  example  is  a  decorative  edge  on  a 
skirting  board.  The machine  is  supplied  with  two  chucks  for 8 
mm  and  12  mm.  Numerous  cutting  heads  are  available  for 
different profiles. 
Some  heads  are  too  large  and  leave  no  space  for  the  dust-
extraction  system.  In  this  casep  a  mask  should  be  worn. 

CAUTION

:  Ensure  that  the  machine  is  not  connected  to  the 

power  supply.  To  insert  the  chuck,  locate  the  spindle  lock  at 
the  front  of  the  machine.  Press  it  down  and  hold  it  in  this 
position.  Using  the  wrench  provided,  loosen  the  chuck  nut  by 
turning  in  an  anticlockwise  direction  (10).  Remove  the  chuck 
and  clean  the  spindle  (11).  Insert  the  other  chuck  in  the 
spindle  and  screw  on  the  nut  finger  tight.  To  insert  a  cutter 
head,  loosen  the  chuck  nut  and  insert  the  shaft  of  the  cutter 
head (12). Ensure thai at least 20 mm or halt the length of the 
cutter-head shaft is inserted into the chuck. If insertion depth is 
less,  the  cutter  head  will  be  instable  and  may  work  loose. 
Press the spindle lock, hold it in position, and tighten the chuck 
nut.  Repeatedly  check  the  tightness  of  the  nut  during  your 
work. 

CAUTION

:  Handle  the  cutter  heads  carefully.  They  are  sharp 

and may cause cuts. 

CAUTION

:  Before  switching  the  machine  on,  ensure  that  the 

chuck nuts are tight. 

7.6 

Cutter guide sleeve 

 

The  cutter  guide  sleeve  is  attached  to  the  base  of  the 
machine  and  ensures  that  the  machine  can  follow  a  certain 
cutting profile. Only certain sizes of cutter head can be used. 
The  si2e  is limited  by  the size  of the  hole in the  cutter  guide 
sleeve. 

 

 

The  dust-extraction  system  can  be  used  with  this  accessory. 
To install the guide plate, lay the cutting machine on its side. 
Loosen  and  remove  the  two  bolts  for  the  dust-extraction 
system.  Remove  the  four  cross-head  screws  attaching  the 
plastic base to the casting (13). Note the recess in the plastic 
base. Hold the guide plate with the sleeve to the outside and 
place it in the recess (14). Align the holes in the plastic base 
with  the  threaded  holes  in  the  casting  and  tighten  the  four 
cross-head  screws  (15).  Re-install  the  dust-extraction 
components and secure it with bolts and nuts.  

Содержание POWX093














Отзывы: