background image

 

POWX07587 

EN

 

Copyright © 2017 VARO NV 

P a g e

 | 

10

 

www.varo.com 

 

Make sure that the turn table is fixed securely.  

 

Make sure that the arm is securely fixed in the working position. Tighten the lever 
clockwise to fix the arm. 

 

Use push stick or push block to avoid working with the hands and fingers close to the saw 
blade. 

 

Make sure the blade is not contacting the riving knife or workpiece before the switch is 
turned on. 

 

Always store the push-stick when it is not in use.  

 

Pay particular attention to instructions for reducing risk of KICKBACK. KICKBACK is 
sudden reaction to pinched, bound or misaligned saw blade. KICKBACK causes the 
ejection of the workpiece from the tool back towards the operator. KICKBACKS CAN 
LEAD TO SERIOUS PERSONAL INJURY. Avoid KICKBACKS by keeping the blade 
sharp, by keeping the rip fence parallel to the blade, by keeping the riving knife and blade 
guard in place and operating properly, by not releasing the workpiece until you have 
pushed it all the way past the blade, and by not ripping workpiece that is twisted or warped 
or does not have straight edge to guide along the fence. 

 

Avoid abrupt, fast feeding. Feed as slowly as possible when cutting hard workpieces. Do 
not bend or twist workpiece while feeding. If you stall or jam the blade in the workpiece, 
turn the tool off immediately. Unplug the tool. Then clear the jam. 

 

Before turning over the tool, always make sure that the stopper pin has securely locked 
the tool head in the lowest position. 

7  INSTALLATION 

CAUTION:  Keep  the  floor  area  around  the  tool  level,  well  maintained  and 
free of loose materials e.g. chips and cut-offs. 

7.1 

Bench mounting (Fig. 1 & 3) 

7.1.1 

For the fully-extended feet set up as the high table.  

When the tool cannot be set up stable, turn the adjusting nut at the foot of the tool for proper 
stability.  Turn  counterclockwise  in  top  viewing  to  make  the  foot  shorter  and  clockwise  in  top 
viewing to make it longer. After adjustment, make sure that the tool keep stable. 

7.1.2 

For the folded feet set up as the low table 

When the tool is ready in the foot-folded position, secure the tool by using U-shaped grooves 
shown in the figure. (fig 3 (4)) 

8  FUNCTIONAL DESCRIPTION 

CAUTION:  Always  be  sure  that  the  tool  is  switched  off  and  unplugged 
before adjusting or checking function on the tool.  

8.1 

Blade guard (Fig. 4, 5 & 6) 

Caution: 

 

Make sure that the handle cannot be lowered without pushing the lever nearby the handle 
to the left. (fig 2 

– (19) 

 

Make sure that the lower blade guards A dose not open unless the lever near the handle 
is pushed at the topmost position of the handle. 

 

Make sure that the lower blade guard C is installed before using in Mitre saw mode. 

 

 

Содержание POWX07587

























Отзывы: