background image

 

POWX07562 

EN

 

Copyright © 2017 VARO 

P a g e

 | 

8

 

www.varo.com 

10 REPLACING THE SAW BLADE (FIG. 8) 

 

Pull out the power plug. 

 

Swing up the machine head (4). 

 

Press release lever (2) sideways. 

 

Move guard upwards and secure hex key in flange bolt (28) 

 

Press the saw shaft lock with one hand while holding the wrench on the flange bolt with 
the other hand. 

 

Firmly press on the saw shaft lock (27) and slowly rotate the flange bolt (28) in clockwise 
direction until it is completely removed. 

 

Remove flange (29) 

 

Take the blade (5) off the inner flange and pull out downwards. 

 

Mount the new saw blade in reverse order and fasten. 

 

Important! The cutting bevel of the teeth, i.e. the direction of rotation of the saw blade, has 
to conform with the direction of the arrow marked on the housing. 

 

Clean the saw blade flanges thoroughly before mounting the saw blade. 

 

Reattach the movable blade guard (6) in reverse order. 

 

Before using the saw again, check that the safety devices are in good working order. 

 

Important: Every time that you change the saw blade, check to see that it spins freely in 
the groove of the turntable in both perpendicular and 45° angle settings. 

11 LASER FUNCTION (FIG. 9) 

You can switch the laser ON and OFF with the switch (31). 
The laser (32) directs a beam onto the work-piece. 
Extremely precise cuts can be made using the laser function. 

12 CLEANING AND MAINTENANCE 

Attention! Before performing any work on the equipment, pull the power 
plug. 

12.1 

Maintenance 

 

Keep the ventilation slots of the tool clean to prevent overheating of the engine. 

 

Remove dust and dirt regularly from the machine. Cleaning is best done with compressed 
air or a rag. 

 

Re-lubricate all moving parts in regular intervals. 

 

Never use caustic agents to clean plastic parts. 

Never use solvents such as petrol, alcohol, ammonia water, etc. These 
solvents may damage the plastic parts. 

13 SERVICE DEPARTMENT 

 

Damaged switches must be replaced by our after-sales service department. 

 

If the connecting cable (or mains plug) is damaged, it must be replaced by a particular 
connecting cable which is available from our service department. Replacement of the 
connecting cable must only be carried out by our service department (see last page) or by 
a qualified person (qualified electrician). 

 

 

Содержание POWX07562












Отзывы: