Quick Setup
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
Choose a location
Keep the projector level and place it at a height so its lens is even with the top
or bottom of the screen and is centered horizontally. If this isn’t possible, use
the lens shift feature or the keystone correction button on the projector to
reposition the image (see “Adjust the image”).
In order to view 3D images correctly, RF 3D glasses must be worn within 32 feet
(10 m) of the projector. Use the image below to determine the viewing distance
for 3D projection (the shading represents the 3D viewing area):
See the online User’s Guide for more information on where to place your
projector.
Connect the projector
Choose from the following connections. For additional connection types, see
the online User’s Guide.
Video device
1
If necessary, remove the cover as shown below.
2
Connect multiple video devices and use the Source buttons on the remote
control or the
button on the projector to switch between them.
HDMI cable
Optical HDMI
Note:
When connecting a source that requires HDCP 2.2, you must use
the HDMI1 port.
WirelessHD™ Transmitter (PowerLite Home Cinema
5040UBe only)
Follow these steps to set up the included WirelessHD Transmitter.
HDMI
1
Place the transmitter within 32 feet (10 m) of the projector. Make sure the
front of the transmitter faces the front of the projector. See the online
User’s Guide for more information on the WirelessHD transmission range.
32 ft
(10 m)
16 ft
(5 m)
32 ft (10 m)
16 ft (5 m)
Note:
Do not place the transmitter on a metal surface, as this may
interfere with the signal. Make sure there are no obstructions between
the transmitter and the projector.
2
Plug the AC adapter into the transmitter and a wall outlet.
3
Connect the HDMI cables to your video input devices and the HDMI ports
on the side and back of the transmitter. You can connect up to four input
devices to the transmitter. See “Viewing WirelessHD content” on the back
of this sheet for information on switching between input sources.
Note:
You can connect tablets, smartphones, and other devices that
support the MHL™ standard to the HDMI port on the side of the
WirelessHD Transmitter. Some devices may require an adapter or may not
require an MHL cable. Not all features or functions may be supported.
Check your device’s documentation for more information.
4
To use the transmitter as a pass-through device to a television or other
display, connect an HDMI cable to the display device and the HDMI output
port on the rear of the transmitter. See “Viewing WirelessHD content” on
the back of this sheet for information on switching between wireless and
wired display modes.
Turn on your equipment
1
Turn on your video source.
2
Plug in the projector.
3
Press the
power button on the projector or the
On
button on the
remote control. The shutter opens and the
power light flashes blue,
then stays on.
Note:
To shut down the projector, press the
power button on the
projector or the
Standby
button on the remote control, then press the
button again to confirm, if necessary. Wait for cooldown to complete
before unplugging the projector.
4
Use the arrow buttons on the remote control to highlight any of the
options on the Home screen that appears, then press
Enter
to select it.
You can display a QR code, switch between projection sources, and quickly
access various adjustment options from this screen.
5
The default language of the menu system is English. To select another
language, press the
Menu
button on the projector or remote control.
Select
Extended
and press
Enter
. Select
Language
and press
Enter
.
Select your language and press
Enter
. Press the
Menu
button to exit
the menu system.
Using the remote control
Install the batteries as shown (two AA batteries).
Choose which source to
display
Turn projector on
Access projector menus
Adjust zoom, focus,
and lens shift
Turn off projector
display
Navigate projector
menus
Control WirelessHD
functions
Turn projector off
Control connected
sources with HDMI
Link
For more information on using the remote control, see the online User’s
Guide.
Adjust the image
1
Press the
Pattern
button on the remote control to display a test pattern.
2
To raise the image or correct a tilted image, adjust the front feet as
shown below.
3
Press the
Lens
button on the remote control and use the and
buttons to focus the image.
PowerLite
®
Home Cinema 5040UB/5040UBe
