background image

Remote Control Transmitter Fob-CM1

Programming Instructions

Pairing Key-Fob Remote Control:

1.  Press and hold the PROGRAM button on the top of the 

unit for 3 seconds until the LED turns green (HPU will also 
beep). The unit is now ready to be paired with the key-fob 
remote control.

NOTE

: If dual units are installed, repeat Steps 1–3 to pair 

multiple units to a single remote control. Up to (10) 
wireless controllers can be programmed to each unit.

2.  Press the UP button on the key-fob remote control for one 

second and release. The green LED on the unit(s) will 
initially turn off, then flash green steadily (HPU will also 
beep) indicating that the pairing is complete.

3.  Test the paired remote control by pressing the UP  

and the  DOWN button to ensure that the anchor  
is responding.

PROGRAM

LED

Hydraulic Pump Unit (HPU)

MICRO Driver Unit

LED

PROGRAM

2

9010 Palm River Road, Tampa, FL 33619

phone 813.689.9932 • fax 813. 689.8883

www.power-pole.com

Need help? Contact our Technical Support Team at 

1 + 813.689.9932 Option 2

©2018 all rights reserved. Power-Pole Shallow Water Anchor 

U.S. Patent No. 6,041,730 

To raise or lower the spike, press and hold either the 

UP

 or 

DOWN

 button on the remote control. The anchor will only 

continue to move so long as you keep the button depressed.

Auto Mode

: Double tapping (pressing and releasing 2 times 

within 1 second) either the 

UP

 or the 

DOWN

 buttonon the 

remote control will cause the anchor to retract or deploy au-
tomatically. The anchor will continue to move in said direction 
until it either retracts completely (up) or senses a solid bottom 
surface (down).

Battery Replacement:

1.

  Ensure the surrounding area is as dry as possible to avoid 

any moisture intrusion.

2.

 Use a small screwdriver to remove the Key-Fob cover. (

FIG. 1

)

3.

  Remove the rubber membrane and the circuit board from 

the Key-Fob.

4.

   Remove the battery from the holder on the front of circuit 

board and replace with any CR2032 3V Lithium Coin 
Battery. (

FIG. 2

)

5.

  Place the circuit board and rubber membrane back into 

the Key-Fob base and ensure that the rubber membrane 
is seated properly prior to installing the cover. (

FIG. 3

)

Operating Instructions

For Technical Support Call 813.689.9932 option 2

Programming Instructions

Key Fob Remote Control

Featuring                   Technology

Pairing Key-Fob Remote Control:

1.

  Press and hold the PROGRAM button on the top of the 

unit for 3 seconds until the LED turns green (HPU will 
also beep). The unit is now ready to be paired with the 
key-fob remote control.

NOTE: If dual units are installed, repeat Steps 1–3 to pair 

multiple units to a single remote control. Up to (10) 
wireless controllers can be programmed to each unit.

2.

  Press the UP button on the key-fob remote control for 

one second and release. The green LED on the unit(s) 
will initially turn off, then flash green steadily (HPU will 
also beep) indicating that the pairing is complete.

3.

  Test the paired remote control by pressing the UP  

and the  DOWN button to ensure that the anchor  
is responding.

PROGRAM

LED

Hydraulic Pump Unit (HPU)

MICRO Driver Unit

LED

PROGRAM

To activate your warranty or find a Power-Pole Certified 

Warranty Center, go to 

www.power-pole.com

2

For Technical Support Call 813.689.9932 option 2

9010 Palm River Road, Tampa, FL 33619 • phone 813.689.9932

fax 813. 689.8883 • 

www.power-pole.com

To raise or lower the spike, press and hold either the 

UP

 or 

DOWN

 button on the remote control. The anchor will only 

continue to move so long as you keep the button depressed.

Auto Mode:

 Double tapping (pressing and releasing 2 times 

within 1 second) either the 

UP

 or the 

DOWN

 button 

on the remote control will cause the anchor to retract or 

deploy automatically. The anchor will continue to move 

in said direction until it either retracts completely (up) or 

senses a solid bottom surface (down).

Battery Replacement:

1.

  Ensure the surrounding area is as dry as possible to avoid 

any moisture intrusion.

2.

  Use a small screwdriver to remove the Key-Fob cover. 

(Figure 1)

 

3.

  Remove the rubber membrane and the circuit board from 

the Key-Fob. 

4.

  Remove the battery from the holder on the front of circuit 

board and replace with any 

CR2032 3V

 Lithium Coin 

Battery. 

(Figure 2)

  

5.

  Place the circuit board and rubber membrane back into 

the Key-Fob base and ensure that the rubber membrane 

is seated properly prior to installing the cover. 

(Figure 3)

 

Operating Instructions

Figure 1

Figure 2

Figure 3

For Technical Support Call 813.689.9932 option 2

Programming Instructions

Key Fob Remote Control

Featuring                   Technology

Pairing Key-Fob Remote Control:

1.

  Press and hold the PROGRAM button on the top of the 

unit for 3 seconds until the LED turns green (HPU will 
also beep). The unit is now ready to be paired with the 
key-fob remote control.

NOTE: If dual units are installed, repeat Steps 1–3 to pair 

multiple units to a single remote control. Up to (10) 
wireless controllers can be programmed to each unit.

2.

  Press the UP button on the key-fob remote control for 

one second and release. The green LED on the unit(s) 
will initially turn off, then flash green steadily (HPU will 
also beep) indicating that the pairing is complete.

3.

  Test the paired remote control by pressing the UP  

and the  DOWN button to ensure that the anchor  
is responding.

PROGRAM

LED

Hydraulic Pump Unit (HPU)

MICRO Driver Unit

LED

PROGRAM

To activate your warranty or find a Power-Pole Certified 

Warranty Center, go to 

www.power-pole.com

2

For Technical Support Call 813.689.9932 option 2

9010 Palm River Road, Tampa, FL 33619 • phone 813.689.9932

fax 813. 689.8883 • 

www.power-pole.com

To raise or lower the spike, press and hold either the 

UP

 or 

DOWN

 button on the remote control. The anchor will only 

continue to move so long as you keep the button depressed.

Auto Mode:

 Double tapping (pressing and releasing 2 times 

within 1 second) either the 

UP

 or the 

DOWN

 button 

on the remote control will cause the anchor to retract or 

deploy automatically. The anchor will continue to move 

in said direction until it either retracts completely (up) or 

senses a solid bottom surface (down).

Battery Replacement:

1.

  Ensure the surrounding area is as dry as possible to avoid 

any moisture intrusion.

2.

  Use a small screwdriver to remove the Key-Fob cover. 

(Figure 1)

 

3.

  Remove the rubber membrane and the circuit board from 

the Key-Fob. 

4.

  Remove the battery from the holder on the front of circuit 

board and replace with any 

CR2032 3V

 Lithium Coin 

Battery. 

(Figure 2)

  

5.

  Place the circuit board and rubber membrane back into 

the Key-Fob base and ensure that the rubber membrane 

is seated properly prior to installing the cover. 

(Figure 3)

 

Operating Instructions

Figure 1

Figure 2

Figure 3

For Technical Support Call 813.689.9932 option 2

Programming Instructions

Key Fob Remote Control

Featuring                   Technology

Pairing Key-Fob Remote Control:

1.

  Press and hold the PROGRAM button on the top of the 

unit for 3 seconds until the LED turns green (HPU will 
also beep). The unit is now ready to be paired with the 
key-fob remote control.

NOTE: If dual units are installed, repeat Steps 1–3 to pair 

multiple units to a single remote control. Up to (10) 
wireless controllers can be programmed to each unit.

2.

  Press the UP button on the key-fob remote control for 

one second and release. The green LED on the unit(s) 
will initially turn off, then flash green steadily (HPU will 
also beep) indicating that the pairing is complete.

3.

  Test the paired remote control by pressing the UP  

and the  DOWN button to ensure that the anchor  
is responding.

PROGRAM

LED

Hydraulic Pump Unit (HPU)

MICRO Driver Unit

LED

PROGRAM

To activate your warranty or find a Power-Pole Certified 

Warranty Center, go to 

www.power-pole.com

2

For Technical Support Call 813.689.9932 option 2

9010 Palm River Road, Tampa, FL 33619 • phone 813.689.9932

fax 813. 689.8883 • 

www.power-pole.com

To raise or lower the spike, press and hold either the 

UP

 or 

DOWN

 button on the remote control. The anchor will only 

continue to move so long as you keep the button depressed.

Auto Mode:

 Double tapping (pressing and releasing 2 times 

within 1 second) either the 

UP

 or the 

DOWN

 button 

on the remote control will cause the anchor to retract or 

deploy automatically. The anchor will continue to move 

in said direction until it either retracts completely (up) or 

senses a solid bottom surface (down).

Battery Replacement:

1.

  Ensure the surrounding area is as dry as possible to avoid 

any moisture intrusion.

2.

  Use a small screwdriver to remove the Key-Fob cover. 

(Figure 1)

 

3.

  Remove the rubber membrane and the circuit board from 

the Key-Fob. 

4.

  Remove the battery from the holder on the front of circuit 

board and replace with any 

CR2032 3V

 Lithium Coin 

Battery. 

(Figure 2)

  

5.

  Place the circuit board and rubber membrane back into 

the Key-Fob base and ensure that the rubber membrane 

is seated properly prior to installing the cover. 

(Figure 3)

 

Operating Instructions

Figure 1

Figure 2

Figure 3

To activate your warranty or find a  Power-Pole Certified Warranty Center, 

go to

 www.power-pole.com

Отзывы: