User Manual
Please read and understand all instructions
before use.Retain this manual for future reference.
8008425
Single Power Door Lock
V 2.9
UNPACKING
1.
Carefully remove the parts from the box.
2.
Inspect the parts carefully to make sure the
device was not damaged while shipping.
3.
Do not discard the packaging material until
you have carefully inspected and satisfactorily
operated the device.
WARNING! If any part is missing, do not operate the
device until the missing parts are replaced. Failure to do
so could result in serious personal injury.
INSTALLATION
1.
Carefully remove the door panel.
2.
Since the adjustable steel mounting strap is
optional at this step, you can either attach the
strap to the door structure (see Figure 3) and
mount the power door lock to the strap, or
attach the power door lock onto the
door structure.
DISPOSING OF THE TOOL
If your tool has become damaged beyond repair, do not
throw it out. Bring it to the appropriate recycling facility.
CONTENTS
Universal 2-wire actuator with mounting hardware.
IMPORTANT SAFETY PRECAUTIONS
WARNING! The warnings, cautions and instructions
discussed in this instruction manual cannot cover all
possible conditions and situations that may occur.
Common sense and caution are factors that cannot be
built into this product, but must be supplied by
the operator.
NOTE:
Keep this manual for the safety warnings, precautions
and operating, inspection and maintenance instructions
.
WORK AREA
1.
Operate in a safe work environment. Keep
your work area clean and well lit. Do not use
in damp or wet locations if it may cause a
slipping hazard.
2.
Keep anyone not wearing appropriate safety
equipment away from the work area. Distraction
can cause you to lose control.
PERSONAL SAFETY
1.
Dress properly, wear protective equipment. Use
foot, hand and head protection. Always wear
ANSI approved impact safety goggles, which
must provide both frontal and side protection.
Protect your hands with suitable gloves.
Protect your head from falling objects by
wearing a hard hat. Protective, electrically non-
conductive clothes and non-skid footwear are
recommended when working. Wear steel-toed
boots to prevent injury from falling objects.
2.
Do not over reach; keep proper footing and
balance at all times.
Proper footing and balance enables better
control of tools in unexpected situations.
3.
Keep any articles of clothing, jewelry, hair etc.
away from moving parts. These can be caught
in moving parts, resulting in damage to the
device and/or serious injury.
4.
Stay alert, watch what you are doing and use
your common sense. Do not operate any
machine or tool when you are tired, under the
influence of drugs, alcohol or medications.
ELECTRICAL SAFETY
1.
Disconnect the device from the power source
before servicing.
2.
Protect yourself against electric shocks when
working on electrical equipment. Avoid body
contact with grounded surfaces. There is an
increased chance of electrical shock if your
body is grounded.
CAUTION! All wiring should be performed by a
qualified electrician.
TOOL USE AND CARE
1.
Do not alter any parts of the device. All parts
and accessories are designed with built-in
safety features that may be compromised
if altered.
2.
Make certain that the power source conforms to
the requirements of your equipment.
3.
When wiring an electrically driven device, follow
all electrical and safety codes, as well as the
most recent Canadian Electrical Code (CE) and
the Canadian Centre for Occupational Health
and Safety (CCOHS).
4.
Always disconnect cables from the battery and
ground cable prior to repairs. Always reconnect
cable to the battery and the ground cable after
the repairs.
NOTE:
Both mounting methods must ensure a
suitable position is selected that will not hinder
the window mechanism and is close enough to
operate the existing lock assembly.
3.
Slide the connector rod onto the end hole of
the power door lock. Attach the connector rod
clamp to the connector rod (see Figure 2).
4.
Set the power door lock in the unlock position,
and then tighten the connector rod clamp to the
existing factory door rod supplied with the kit.
5.
Pull the connector rod until the actuator is fully
extended, then tighten the connector rod clamp
to the existing factory door rod.
6.
Connect the blue wire to the positive power
connection and the green wire to the negative
power connection.
