Powell PowlVac IB-65020A CDR 27kV Скачать руководство пользователя

Страница: 48 / 68

Powered by Safety

IB-65020A

Maintenance

is also attached to the circuit breaker

frame near the ground connection on

an engraved metal plate. The serial

number found on the nameplate must

match the number affixed to the frame.

b. Adjustment of Primary & Secondary

Trip Prop

Figure 21 Primary & Secondary Trip Prop

Adjustment

0.005-0.015"

a. Secondary Trip Prop

b. Primary Trip Prop Roller

c. Primary Trip Prop

d. Primary Trip Prop Adjusting Screw

e. Rivet

f. Trip Bar

Perform the following procedures to

adjust the primary trip prop:

1. Remove the main closing spring.

Refer to

Ch 5 Maintenance,

echAnISM

reA

3) Closing Spring

Removal

2. Adjust the primary trip prop

adjusting screw (Figure 21, d) so

that with the fundamental linkage

in the reset position, the clearance

between the primary trip prop

roller and the secondary trip prop

is 0.005” to 0.015”. The primary trip

prop adjusting screw is accessible

from the rear of the stored energy

mechanism and is located inside

the hole beside the lower middle

insulator supporting the live part

assembly.

3. Adjust the secondary trip prop

adjusting screw (Figure 26, c) so that

the secondary trip prop top edge

is in the line of sight with the top

of the rivet of the primary trip prop

roller as shown in Figure 21.

4. Replace the main closing spring

c. Tripping System Adjustment

Prior to performing any adjustment or

maintenance procedure, all high voltage

components shall be deenergized,

disconnected by means of a visible break, and

securely grounded.

WARNING

To adjust the PowlVac® CDR Tripping

System perform the following steps:

1. Prior to performing this adjustment

procedure, all high voltage

components shall be deenergized,

disconnected by means of visible

break and securely grounded, and

ensure that the control circuits are

deenergized.

2. Remove the circuit breaker front

cover.

3. Loosen the secondary trip prop

adjusting screw locking nut several

full turns.

Содержание PowlVac IB-65020A CDR 27kV





































































Результаты поиска

Содержание PowlVac IB-65020A CDR 27kV

Отзывы:

Похожие инструкции для PowlVac IB-65020A CDR 27kV

Бренды по названию

Популярные бренды

Powell PowlVac IB-65020A CDR 27kV, Руководство пользователя

Результаты поиска

Содержание PowlVac IB-65020A CDR 27kV

Отзывы:

Похожие инструкции для PowlVac IB-65020A CDR 27kV

Бренды по названию

Популярные бренды