Poulan Pro 437921 страница 9 Скачать руководство пользователя

Страница: 9 / 40

OPERATION

Drive speed control lever -

used to select forward or

reverse motion and speed of snow thrower.

Traction drive control lever -

used to engage power-pro-

pelled for ward or reverse motion of snow thrower.

Auger control lever -

used to engage auger motion (throw

snow).

Discharge chute control lever -

used to change the di-

rec tion the snow is thrown.

Skid plate -

used to adjust height of scraper bar from the

ground.

Toolbox -

used to store spare shear bolts, locknuts and

wrench.

Safety ignition key -

must be inserted for the engine to

start and run. Remove when snow thrower is not in use.

Electric start button –

used for starting the engine.

Recoil (auxiliary) starter handle –

used for start ing the

en gine.

Primer -

pumps additional fuel from the carburetor to the

cylinder for use when starting a cold engine.

ON / OFF switch -

used to STOP the engine.

Choke control -

used for starting a cold engine.

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

TRACTION

DRIVE

CONTROL

LEVER

DISCHARGE CHUTE

CONTROL LEVER

DRIVE SPEED

CON TROL LEVER

AUGER

CONTROL

LEVER

MUF FLER

TOOLBOX

HANDLE

KNOB

SKID PLATE

CHUTE

DE FLEC TOR

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

Fig. 10

AU GERS

DISCHARGE

CHUTE

CLEAN-OUT TOOL

FUEL SHUT-OFF VALVE

ON / OFF

SWITCH

MUF FLER

GAS O LINE

FILLER CAP

SAFETY

IGNITION

KEY

CHOKE

CON-

TROL

PRIM ER

RECOIL (AUXILIARY) STARTER HANDLE

ELECTRIC

START

BUTTON

POWER

CORD

PLUG

LIGHT

DEFLECTOR REMOTE

CONTROL LEVER

Содержание 437921









































Результаты поиска

Содержание 437921

Отзывы:

Похожие инструкции для 437921

Бренды по названию

Популярные бренды

Poulan Pro 437921, Руководство пользователя

Результаты поиска

Содержание 437921

Отзывы:

Похожие инструкции для 437921

Бренды по названию

Популярные бренды