background image

9401 GB WArtunG (873)

GB

- 1 -

MainTEnanCE anD sErViCE

Spur wheel - angular gear

-  First oil change is after 50 hours of operation.
-  Further oil change after 100 hours of operation.

Amount of oil: 

6 liters SAE 90

-  Park machine horizontally.
-  Remove oil drain plug (90), drain old oil out and dispose of in the 

proper manner.

-  Screw oil drain plug (90) in again.
-  Remove oil filler screw and oil measuring stick (91) and fill until 

oil level reaches "A".

-  Check oil level before putting into operation.

Change speed transmission 

(LION 3000, LION 4000)

-  First oil change is after 50 hours of operation.
-  Further oil change after 100 hours of operation.

Amount of oil: 

4 liters SAE 90

L =   Ventilating screw: is remo-

ved to enable oil filling.

N =  Level  screw: oil level is 

correct  when  it  reaches 

the  same  level  as  the 

screw.

A =   Drain plug.

Advice for general maintence

  In order to keep the implement in good condition even after a 

longer service life, please observe the following advice.

Safety points

•  Tur n  engine  off  when 

adjustment, service and repair 
work is to be done.

•  Do not work under the machine 

without safe support.

-  Retighten all screws after the first hours of operation.
-  Observe maintenance advice for spur wheel - angular gear.
-   The spur wheel gear in the rotor bar is maintenance free.

Changing the tines

  Damaged  or  worn  rotor  tines  are  to  be 

replaced. Observe the correct fitting position 
of each rotor tine (see Spare Parts list). 

  Both screws (SK) are to be glued into place 

with  Loctite  24  or  another  equivalent 
product,  and  tightened  to  290  Nm  (29 
kpm). 

Drive shaft

-  Lubricate drive shaft every 8 hours of operation.
-  Take sliding sections apart and grease well.

Cleaning of machine parts

Attention ! ! !

Do not use a high pressure cleaner to clean bearings and hydraulic 
parts.

-  Danger of rust formation!
-  After cleaning, grease machine according to lubrication chart and 

carry out a short test run.

-  If pressure is to great when cleaning, damage to paintwork can 

occur.

winter storage

-  Thoroughly clean the machine beforehand.
-  Park where protected against weather.
-  Change or top-up gear oil.
-  Protect all exposed sections against rust.
-  Grease all greasing points according to lubrication chart.

Содержание LION 4000








































Отзывы: