background image

900_GB-Anhang A_Sicherheit

SUPPLEMENT - A

Recommendations for work safety 

- A 1 -

20%

Kg

Recommendations for work safety 

All points refering to safety in this manual are indicated 
by this sign.

1.) Defined use

a.  See "Technical Data". 
b.  The keeping of operating, service and maintenance requirements 

layed down by the manufacturer also come under the heading of 
"defined use".

 

2.) Spare parts

a.  The 

original components and accessories have been designed 

 especially for these machines and appliances. 

b.  We want to make it quite clear that components and accesories 

that have not been supplied by us have not been tested by us. 

c.  The  installation  and/or  use  of  such  products  can,  therefore, 

negatively change or influence the construction characteristics 
of the appliance. We are not liable for damages caused by the 
use of components and accessories that have not been supplied 
by us. 

d.  Alterations and the use of auxiliary parts that are not permitted 

by the manufacturer render all liability invalid. 

3.) Protection devices

   All  protection  devices  must  remain  on  the  machine  and  be 

maintained in proper condition. Punctual replacement of worn 
and damaged covers is essential.

4.) Before starting work

a.  Before  commencing  work,  the  operator  must  be  aware  of  all 

operating devices and functions. The learning of these is too late 
after having already commenced operation!

b. The vehicle is to be tested for traffic and operating safety before 

each operation. 

5.) Asbestos 

-  Certain  sub-supplied  components  of  the 

 vehicle may contain asbestos due to technical 
reasons.  Observe  the  warning  on  spare 
parts. 

6.) Transport of persons prohibited

a.  The transport of persons on the machine is not permitted. 
b.  The machine may only be driven on public roads when in the 

position stipulated for road transport. 

7.) Driving ability with auxiliary equipment 

a.  The towing vehicle is to be sufficiently equiped with weights at the 

front or at the rear in order to guarantee the steering and braking 
capacity (a minimum of 20% of the vehicle’s tare weight on the 
front axle).

b.    The  driving  ability  is 

influenced  by  ground 
conditions  and  by  the 
 auxiliary equipment. The 
driving must be adapted 
to  the  corresponding 
 terrain  and  ground 
 conditions. 

c.  When  driving  through 

curves with a connected 
 appliance,  observe  the 
radius  and  swinging 
mass of the appliance. 

d.  When  travelling  in  a  curve  with  attached  or  semimounted 

implements, take into account the working range and swing mass 
of the implement!

8.) General 

a.  Before attaching implement to three-point linkage, move system 

lever into a position whereby unintentional raising or lowering is 
ruled out!

b.  Danger of injury exists when coupling implement to tractor!
c.  Danger of injury through crushing and cutting exists in the three-

point linkage area!

d.  Do not stand between tractor and implement when using three-

point linkage external operation!

e.  Attach and detach drive shaft only when motor has stopped.
f.  When transporting with raised implement, secure operating lever 

against lowering! 

g.  Before leaving tractor, lower attached implement to the ground 

and remove ignition key!

h.  Nobody is to stand between tractor and implement without tractor 

being secured against rolling using parking brake and/or wheel 
chocks!

i.   For all maintenance, service and modification work, turn driving 

motor off and remove universal drive.

9.) Cleaning the machine

   Do not use high-pressure washers for the cleaning of bearing- and 

hydraulic parts.

Содержание HIT 470 N































Отзывы: