background image

- 2 -

9500-GB STörUNGEN_511

GB

trouBleshooting

Troubleshooting

Any machine is liable to develop faults now and again. The list below is intended to make curing them easier. Never delay in finding 

a remedy. 

Faults

Torque limiter on driveshaft triggered.

A transmission runs hot.

Scraper  floor  chain  runs  noisily  (ticking 

over).

noise from transmission chain.

Forage jams.

Poor cutting quality.

Jockey wheels do not reach ground.

Forage is picked up soiled.

hydraulic mechanism move jerkily.

Tailgate does not swing.

Poor braking.

Remedies

Declutch and start off again at low revs.

If  necessary  remove  foreign  body  and 

sharpen  knives.  For  blockages  in  the 

pressing channel, remove eccentric lock 

on cutter bar, switch press on (cutter bar 

swings  out  automatically),  swing  cutter 

bar in again.

Top up or replace oil.

Check chain tension.

Check chain tension regularly (5 to  mm 

play), tighten if necessary.

Set drawbar to correct height.

Sharpen knives in time or replace them. 

Drive at lower revs, so that larger wads 

of forage are picked up.

Adjust  jockey  wheels  and  check  height 

setting at hitch. 

Check jockey wheel setting.

Loosen  bleed  screws  (A)  and  bleed 

lines.

Undo union nut (

) on cylinder, drain 

a little oil and replace nut, if necessary 

bleed air off and clean coil.

Adjust or replace linings.

Causes

Too much forage at once, large foreign 

body or blunt knives.

no lubrication.

Chain too loose or too taut.

Chain loose.

Travel speed too high, trailer hitched up 

too low.

Blunt knives,

p.t.o. speed too high.

Pick-up set wrong.

Jockey wheels set too low.

Air in lines or cylinders.

Coil (

) dirty.

Brake linings worn.

A

TD2/5/7

Содержание BOSS L 22T
















































Отзывы: