Potterton Paramount four Скачать руководство пользователя страница 12

Страница: 12 / 144

3 Technical specifications

3.1 Homologations

3.1.1 Regulations and standards

Beside the general technical rules, the relevant standards, regulations, or

dinances and guidelines should be followed:

DIN 4109; Noise protection in construction engineering

DIN EN 12828; Heating systems in buildings

Federal Immission Control Ordinance 3. BImSchV

DVGW-TRGI 2008 (DVGW worksheet G 600); Technical rules for gas

installation

TRF; Technical rules LPG

DVGW code of practice G 613; Gas appliances - Installation, mainte

nance and operating instructions

DIN 18380; Heating plants and central hot water plants (VOB)

DIN EN 12831; Heating plants in buildings

DIN 4753-6: Domestic hot water calorifiers Domestic hot water heating

system and storage tanks for heated water

DIN 1988; Technical Rules for drinking water installations (TRWI)

DIN EN 60335-2-102: Safety of electrical appliances for household use

and similar purposes: Special requirements for gas-, oil- und solid fuel

appliances with electrical connections

Fuel Ordinance, State Ordinances

Regulations of the local Electricity Board

Obligation to register (possibly. Group Exemption Regulation )

ATV-Code-of-practice M251 of the waste water technology association

Regulations of the public authorities for the run-off of condensate.

3.2 Technical data

3.2.1 Technical data – Boiler space heaters

Tab.2

Technical parameters for boiler space heaters

Model

Paramount four

Condensing boiler

Yes

Low-temperature boiler

(1)

B1 boiler

Cogeneration space heater

Combination heater

Rated heat output

Prated

Useful heat output at rated heat output and high tem

perature mode

(2)

29.2

36.8

Useful heat output at 30 % of rated heat output and low

temperature mode

(1)

9.8

12.3

Seasonal space heating energy efficiency

Useful efficiency at rated heat output and high temper

ature mode

(2)(2)

87.6

87.7

Useful heat output at 30 % of rated heat output and low

temperature mode

(1)

97.9

97,8

Auxiliary power consumption

At full load

elmax

0.055

0.070

At part load

elmin

0.021

0.025

3 Technical specifications

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Содержание Paramount four

















































































































































Результаты поиска

Содержание Paramount four

Отзывы:

Potterton Paramount four, Руководство по установке, Страница: 12 / 144

Результаты поиска

Содержание Paramount four

Отзывы: